| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from can and netfilter.
Current release - regressions:
- rtnetlink: try the outer netns attribute in rtnl_get_peer_net()
- rust: net::phy fix module autoloading
Current release - new code bugs:
- phy: avoid undefined behavior in *_led_polarity_set()
- eth: octeontx2-pf: fix netdev memory leak in rvu_rep_create()
Previous releases - regressions:
- smc: check sndbuf_space again after NOSPACE flag is set in smc_poll
- ipvs: fix clamp() of ip_vs_conn_tab on small memory systems
- dsa: restore dsa_software_vlan_untag() ability to operate on
VLAN-untagged traffic
- eth:
- tun: fix tun_napi_alloc_frags()
- ionic: no double destroy workqueue
- idpf: trigger SW interrupt when exiting wb_on_itr mode
- rswitch: rework ts tags management
- team: fix feature exposure when no ports are present
Previous releases - always broken:
- core: fix repeated netlink messages in queue dump
- mdiobus: fix an OF node reference leak
- smc: check iparea_offset and ipv6_prefixes_cnt when receiving
proposal msg
- can: fix missed interrupts with m_can_pci
- eth: oa_tc6: fix infinite loop error when tx credits becomes 0"
* tag 'net-6.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (45 commits)
net: mctp: handle skb cleanup on sock_queue failures
net: mdiobus: fix an OF node reference leak
octeontx2-pf: fix error handling of devlink port in rvu_rep_create()
octeontx2-pf: fix netdev memory leak in rvu_rep_create()
psample: adjust size if rate_as_probability is set
netdev-genl: avoid empty messages in queue dump
net: dsa: restore dsa_software_vlan_untag() ability to operate on VLAN-untagged traffic
selftests: openvswitch: fix tcpdump execution
net: usb: qmi_wwan: add Quectel RG255C
net: phy: avoid undefined behavior in *_led_polarity_set()
netfilter: ipset: Fix for recursive locking warning
ipvs: Fix clamp() of ip_vs_conn_tab on small memory systems
can: m_can: fix missed interrupts with m_can_pci
can: m_can: set init flag earlier in probe
rtnetlink: Try the outer netns attribute in rtnl_get_peer_net().
net: netdevsim: fix nsim_pp_hold_write()
idpf: trigger SW interrupt when exiting wb_on_itr mode
idpf: add support for SW triggered interrupts
qed: fix possible uninit pointer read in qed_mcp_nvm_info_populate()
net: ethernet: bgmac-platform: fix an OF node reference leak
...
|
|
fwnode_find_mii_timestamper() calls of_parse_phandle_with_fixed_args()
but does not decrement the refcount of the obtained OF node. Add an
of_node_put() call before returning from the function.
This bug was detected by an experimental static analysis tool that I am
developing.
Fixes: bc1bee3b87ee ("net: mdiobus: Introduce fwnode_mdiobus_register_phy()")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241218035106.1436405-1-joe@pf.is.s.u-tokyo.ac.jp
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Unregister the devlink port when register_netdev() fails.
Fixes: 9ed0343f561e ("octeontx2-pf: Add devlink port support")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Link: https://patch.msgid.link/20241217052326.1086191-2-harshit.m.mogalapalli@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When rvu_rep_devlink_port_register() fails, free_netdev(ndev) for this
incomplete iteration before going to "exit:" label.
Fixes: 9ed0343f561e ("octeontx2-pf: Add devlink port support")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Link: https://patch.msgid.link/20241217052326.1086191-1-harshit.m.mogalapalli@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
idpf: trigger SW interrupt when exiting wb_on_itr mode
Joshua Hay says:
This patch series introduces SW triggered interrupt support for idpf,
then uses said interrupt to fix a race condition between completion
writebacks and re-enabling interrupts.
* '200GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
idpf: trigger SW interrupt when exiting wb_on_itr mode
idpf: add support for SW triggered interrupts
====================
Link: https://patch.msgid.link/20241217225715.4005644-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2024-12-18
There are 2 patches by Matthias Schiffer for the m_can_pci driver that
handles the m_can cores found on the Intel Elkhart Lake processor.
They fix the initialization and the interrupt handling under high CAN
bus load.
* tag 'linux-can-fixes-for-6.13-20241218' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: m_can: fix missed interrupts with m_can_pci
can: m_can: set init flag earlier in probe
====================
Link: https://patch.msgid.link/20241218121722.2311963-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for Quectel RG255C which is based on Qualcomm SDX35 chip.
The composition is DM / NMEA / AT / QMI.
T: Bus=01 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=0316 Rev= 5.15
S: Manufacturer=Quectel
S: Product=RG255C-CN
S: SerialNumber=c68192c1
C:* #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=86(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Martin Hou <martin.hou@foxmail.com>
Link: https://patch.msgid.link/tencent_17DDD787B48E8A5AB8379ED69E23A0CD9309@qq.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
gcc runs into undefined behavior at the end of the three led_polarity_set()
callback functions if it were called with a zero 'modes' argument and it
just ends the function there without returning from it.
This gets flagged by 'objtool' as a function that continues on
to the next one:
drivers/net/phy/aquantia/aquantia_leds.o: warning: objtool: aqr_phy_led_polarity_set+0xf: can't find jump dest instruction at .text+0x5d9
drivers/net/phy/intel-xway.o: warning: objtool: xway_gphy_led_polarity_set() falls through to next function xway_gphy_config_init()
drivers/net/phy/mxl-gpy.o: warning: objtool: gpy_led_polarity_set() falls through to next function gpy_led_hw_control_get()
There is no point to micro-optimize the behavior here to save a single-digit
number of bytes in the kernel, so just change this to a "return -EINVAL"
as we do when any unexpected bits are set.
Fixes: 1758af47b98c ("net: phy: intel-xway: add support for PHY LEDs")
Fixes: 9d55e68b19f2 ("net: phy: aquantia: correctly describe LED polarity override")
Fixes: eb89c79c1b8f ("net: phy: mxl-gpy: correctly describe LED polarity")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241217081056.238792-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The interrupt line of PCI devices is interpreted as edge-triggered,
however the interrupt signal of the m_can controller integrated in Intel
Elkhart Lake CPUs appears to be generated level-triggered.
Consider the following sequence of events:
- IR register is read, interrupt X is set
- A new interrupt Y is triggered in the m_can controller
- IR register is written to acknowledge interrupt X. Y remains set in IR
As at no point in this sequence no interrupt flag is set in IR, the
m_can interrupt line will never become deasserted, and no edge will ever
be observed to trigger another run of the ISR. This was observed to
result in the TX queue of the EHL m_can to get stuck under high load,
because frames were queued to the hardware in m_can_start_xmit(), but
m_can_finish_tx() was never run to account for their successful
transmission.
On an Elkhart Lake based board with the two CAN interfaces connected to
each other, the following script can reproduce the issue:
ip link set can0 up type can bitrate 1000000
ip link set can1 up type can bitrate 1000000
cangen can0 -g 2 -I 000 -L 8 &
cangen can0 -g 2 -I 001 -L 8 &
cangen can0 -g 2 -I 002 -L 8 &
cangen can0 -g 2 -I 003 -L 8 &
cangen can0 -g 2 -I 004 -L 8 &
cangen can0 -g 2 -I 005 -L 8 &
cangen can0 -g 2 -I 006 -L 8 &
cangen can0 -g 2 -I 007 -L 8 &
cangen can1 -g 2 -I 100 -L 8 &
cangen can1 -g 2 -I 101 -L 8 &
cangen can1 -g 2 -I 102 -L 8 &
cangen can1 -g 2 -I 103 -L 8 &
cangen can1 -g 2 -I 104 -L 8 &
cangen can1 -g 2 -I 105 -L 8 &
cangen can1 -g 2 -I 106 -L 8 &
cangen can1 -g 2 -I 107 -L 8 &
stress-ng --matrix 0 &
To fix the issue, repeatedly read and acknowledge interrupts at the
start of the ISR until no interrupt flags are set, so the next incoming
interrupt will also result in an edge on the interrupt line.
While we have received a report that even with this patch, the TX queue
can become stuck under certain (currently unknown) circumstances on the
Elkhart Lake, this patch completely fixes the issue with the above
reproducer, and it is unclear whether the remaining issue has a similar
cause at all.
Fixes: cab7ffc0324f ("can: m_can: add PCI glue driver for Intel Elkhart Lake")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://patch.msgid.link/fdf0439c51bcb3a46c21e9fb21c7f1d06363be84.1728288535.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
While an m_can controller usually already has the init flag from a
hardware reset, no such reset happens on the integrated m_can_pci of the
Intel Elkhart Lake. If the CAN controller is found in an active state,
m_can_dev_setup() would fail because m_can_niso_supported() calls
m_can_cccr_update_bits(), which refuses to modify any other configuration
bits when CCCR_INIT is not set.
To avoid this issue, set CCCR_INIT before attempting to modify any other
configuration flags.
Fixes: cd5a46ce6fa6 ("can: m_can: don't enable transceiver when probing")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://patch.msgid.link/e247f331cb72829fcbdfda74f31a59cbad1a6006.1728288535.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
nsim_pp_hold_write() has two problems:
1) It may return with rtnl held, as found by syzbot.
2) Its return value does not propagate an error if any.
Fixes: 1580cbcbfe77 ("net: netdevsim: add some fake page pool use")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241216083703.1859921-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is a race condition between exiting wb_on_itr and completion write
backs. For example, we are in wb_on_itr mode and a Tx completion is
generated by HW, ready to be written back, as we are re-enabling
interrupts:
HW SW
| |
| | idpf_tx_splitq_clean_all
| | napi_complete_done
| |
| tx_completion_wb | idpf_vport_intr_update_itr_ena_irq
That tx_completion_wb happens before the vector is fully re-enabled.
Continuing with this example, it is a UDP stream and the
tx_completion_wb is the last one in the flow (there are no rx packets).
Because the HW generated the completion before the interrupt is fully
enabled, the HW will not fire the interrupt once the timer expires and
the write back will not happen. NAPI poll won't be called. We have
indicated we're back in interrupt mode but nothing else will trigger the
interrupt. Therefore, the completion goes unprocessed, triggering a Tx
timeout.
To mitigate this, fire a SW triggered interrupt upon exiting wb_on_itr.
This interrupt will catch the rogue completion and avoid the timeout.
Add logic to set the appropriate bits in the vector's dyn_ctl register.
Fixes: 9c4a27da0ecc ("idpf: enable WB_ON_ITR")
Reviewed-by: Madhu Chittim <madhu.chittim@intel.com>
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
SW triggered interrupts are guaranteed to fire after their timer
expires, unlike Tx and Rx interrupts which will only fire after the
timer expires _and_ a descriptor write back is available to be processed
by the driver.
Add the necessary fields, defines, and initializations to enable a SW
triggered interrupt in the vector's dyn_ctl register.
Reviewed-by: Madhu Chittim <madhu.chittim@intel.com>
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Coverity reports an uninit pointer read in qed_mcp_nvm_info_populate().
If EOPNOTSUPP is returned from qed_mcp_bist_nvm_get_num_images() ensure
nvm_info.num_images is set to 0 to avoid possible uninit assignment
to p_hwfn->nvm_info.image_att later on in out label.
Closes: https://scan5.scan.coverity.com/#/project-view/63204/10063?selectedIssue=1636666
Suggested-by: Simon Horman <horms@kernel.org>
Signed-off-by: Gianfranco Trad <gianf.trad@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241215011733.351325-2-gianf.trad@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The OF node obtained by of_parse_phandle() is not freed. Call
of_node_put() to balance the refcount.
This bug was found by an experimental static analysis tool that I am
developing.
Fixes: 1676aba5ef7e ("net: ethernet: bgmac: device tree phy enablement")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241214014912.2810315-1-joe@pf.is.s.u-tokyo.ac.jp
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
There are two skb pointers to manage tx skb's enqueued from n/w stack.
waiting_tx_skb pointer points to the tx skb which needs to be processed
and ongoing_tx_skb pointer points to the tx skb which is being processed.
SPI thread prepares the tx data chunks from the tx skb pointed by the
ongoing_tx_skb pointer. When the tx skb pointed by the ongoing_tx_skb is
processed, the tx skb pointed by the waiting_tx_skb is assigned to
ongoing_tx_skb and the waiting_tx_skb pointer is assigned with NULL.
Whenever there is a new tx skb from n/w stack, it will be assigned to
waiting_tx_skb pointer if it is NULL. Enqueuing and processing of a tx skb
handled in two different threads.
Consider a scenario where the SPI thread processed an ongoing_tx_skb and
it moves next tx skb from waiting_tx_skb pointer to ongoing_tx_skb pointer
without doing any NULL check. At this time, if the waiting_tx_skb pointer
is NULL then ongoing_tx_skb pointer is also assigned with NULL. After
that, if a new tx skb is assigned to waiting_tx_skb pointer by the n/w
stack and there is a chance to overwrite the tx skb pointer with NULL in
the SPI thread. Finally one of the tx skb will be left as unhandled,
resulting packet missing and memory leak.
- Consider the below scenario where the TXC reported from the previous
transfer is 10 and ongoing_tx_skb holds an tx ethernet frame which can be
transported in 20 TXCs and waiting_tx_skb is still NULL.
tx_credits = 10; /* 21 are filled in the previous transfer */
ongoing_tx_skb = 20;
waiting_tx_skb = NULL; /* Still NULL */
- So, (tc6->ongoing_tx_skb || tc6->waiting_tx_skb) becomes true.
- After oa_tc6_prepare_spi_tx_buf_for_tx_skbs()
ongoing_tx_skb = 10;
waiting_tx_skb = NULL; /* Still NULL */
- Perform SPI transfer.
- Process SPI rx buffer to get the TXC from footers.
- Now let's assume previously filled 21 TXCs are freed so we are good to
transport the next remaining 10 tx chunks from ongoing_tx_skb.
tx_credits = 21;
ongoing_tx_skb = 10;
waiting_tx_skb = NULL;
- So, (tc6->ongoing_tx_skb || tc6->waiting_tx_skb) becomes true again.
- In the oa_tc6_prepare_spi_tx_buf_for_tx_skbs()
ongoing_tx_skb = NULL;
waiting_tx_skb = NULL;
- Now the below bad case might happen,
Thread1 (oa_tc6_start_xmit) Thread2 (oa_tc6_spi_thread_handler)
--------------------------- -----------------------------------
- if waiting_tx_skb is NULL
- if ongoing_tx_skb is NULL
- ongoing_tx_skb = waiting_tx_skb
- waiting_tx_skb = skb
- waiting_tx_skb = NULL
...
- ongoing_tx_skb = NULL
- if waiting_tx_skb is NULL
- waiting_tx_skb = skb
To overcome the above issue, protect the moving of tx skb reference from
waiting_tx_skb pointer to ongoing_tx_skb pointer and assigning new tx skb
to waiting_tx_skb pointer, so that the other thread can't access the
waiting_tx_skb pointer until the current thread completes moving the tx
skb reference safely.
Fixes: 53fbde8ab21e ("net: ethernet: oa_tc6: implement transmit path to transfer tx ethernet frames")
Signed-off-by: Parthiban Veerasooran <parthiban.veerasooran@microchip.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
SPI thread wakes up to perform SPI transfer whenever there is an TX skb
from n/w stack or interrupt from MAC-PHY. Ethernet frame from TX skb is
transferred based on the availability tx credits in the MAC-PHY which is
reported from the previous SPI transfer. Sometimes there is a possibility
that TX skb is available to transmit but there is no tx credits from
MAC-PHY. In this case, there will not be any SPI transfer but the thread
will be running in an endless loop until tx credits available again.
So checking the availability of tx credits along with TX skb will prevent
the above infinite loop. When the tx credits available again that will be
notified through interrupt which will trigger the SPI transfer to get the
available tx credits.
Fixes: 53fbde8ab21e ("net: ethernet: oa_tc6: implement transmit path to transfer tx ethernet frames")
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Parthiban Veerasooran <parthiban.veerasooran@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
There is a check for NULL at the start of create_txqs() and
create_rxqs() which tess if "nic_dev->txqs" is non-NULL. The
intention is that if the device is already open and the queues
are already created then we don't create them a second time.
However, the bug is that if we have an error in the create_txqs()
then the pointer doesn't get set back to NULL. The NULL check
at the start of the function will say that it's already open when
it's not and the device can't be used.
Set ->txqs back to NULL on cleanup on error.
Fixes: c3e79baf1b03 ("net-next/hinic: Add logical Txq and Rxq")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/0cc98faf-a0ed-4565-a55b-0fa2734bc205@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Small follow-up to align this to an equivalent behavior as the bond driver.
The change in 3625920b62c3 ("teaming: fix vlan_features computing") removed
the netdevice vlan_features when there is no team port attached, yet it
leaves the full set of enc_features intact.
Instead, leave the default features as pre 3625920b62c3, and recompute once
we do have ports attached. Also, similarly as in bonding case, call the
netdev_base_features() helper on the enc_features.
Fixes: 3625920b62c3 ("teaming: fix vlan_features computing")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20241213123657.401868-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The "gl->tot_len" variable is controlled by the user. It comes from
process_responses(). On 32bit systems, the "gl->tot_len +
sizeof(struct cpl_pass_accept_req) + sizeof(struct rss_header)" addition
could have an integer wrapping bug. Use size_add() to prevent this.
Fixes: a08943947873 ("crypto: chtls - Register chtls with net tls")
Cc: stable@vger.kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/c6bfb23c-2db2-4e1b-b8ab-ba3925c82ef5@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The existing linked list based implementation of how ts tags are
assigned and managed is unsafe against concurrency and corner cases:
- element addition in tx processing can race against element removal
in ts queue completion,
- element removal in ts queue completion can race against element
removal in device close,
- if a large number of frames gets added to tx queue without ts queue
completions in between, elements with duplicate tag values can get
added.
Use a different implementation, based on per-port used tags bitmaps and
saved skb arrays.
Safety for addition in tx processing vs removal in ts completion is
provided by:
tag = find_first_zero_bit(...);
smp_mb();
<write rdev->ts_skb[tag]>
set_bit(...);
vs
<read rdev->ts_skb[tag]>
smp_mb();
clear_bit(...);
Safety for removal in ts completion vs removal in device close is
provided by using atomic read-and-clear for rdev->ts_skb[tag]:
ts_skb = xchg(&rdev->ts_skb[tag], NULL);
if (ts_skb)
<handle it>
Fixes: 33f5d733b589 ("net: renesas: rswitch: Improve TX timestamp accuracy")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Link: https://patch.msgid.link/20241212062558.436455-1-nikita.yoush@cogentembedded.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some calls into ionic_get_module_eeprom() don't use a single
full buffer size, but instead multiple calls with an offset.
Teach our driver to use the offset correctly so we can
respond appropriately to the caller.
Fixes: 4d03e00a2140 ("ionic: Add initial ethtool support")
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20241212213157.12212-4-shannon.nelson@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There are some FW error handling paths that can cause us to
try to destroy the workqueue more than once, so let's be sure
we're checking for that.
The case where this popped up was in an AER event where the
handlers got called in such a way that ionic_reset_prepare()
and thus ionic_dev_teardown() got called twice in a row.
The second time through the workqueue was already destroyed,
and destroy_workqueue() choked on the bad wq pointer.
We didn't hit this in AER handler testing before because at
that time we weren't using a private workqueue. Later we
replaced the use of the system workqueue with our own private
workqueue but hadn't rerun the AER handler testing since then.
Fixes: 9e25450da700 ("ionic: add private workqueue per-device")
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20241212213157.12212-3-shannon.nelson@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If register_netdev() fails, then the driver leaks the netdev notifier.
Fix this by calling ionic_lif_unregister() on register_netdev()
failure. This will also call ionic_lif_unregister_phc() if it has
already been registered.
Fixes: 30b87ab4c0b3 ("ionic: remove lif list concept")
Signed-off-by: Brett Creeley <brett.creeley@amd.com>
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20241212213157.12212-2-shannon.nelson@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If either a zero count or a large one is provided, kernel can crash.
Fixes: 82c93a87bf8b ("netdevsim: implement couple of testing devlink health reporters")
Reported-by: syzbot+ea40e4294e58b0292f74@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/675c6862.050a0220.37aaf.00b1.GAE@google.com/T/#u
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Link: https://patch.msgid.link/20241213172518.2415666-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Packets injected by the CPU should have a SRC_PORT field equal to the
CPU port module index in the Analyzer block (ocelot->num_phys_ports).
The blamed commit copied the ocelot_ifh_set_basic() call incorrectly
from ocelot_xmit_common() in net/dsa/tag_ocelot.c. Instead of calling
with "x", it calls with BIT_ULL(x), but the field is not a port mask,
but rather a single port index.
[ side note: this is the technical debt of code duplication :( ]
The error used to be silent and doesn't appear to have other
user-visible manifestations, but with new changes in the packing
library, it now fails loudly as follows:
------------[ cut here ]------------
Cannot store 0x40 inside bits 46-43 - will truncate
sja1105 spi2.0: xmit timed out
WARNING: CPU: 1 PID: 102 at lib/packing.c:98 __pack+0x90/0x198
sja1105 spi2.0: timed out polling for tstamp
CPU: 1 UID: 0 PID: 102 Comm: felix_xmit
Tainted: G W N 6.13.0-rc1-00372-gf706b85d972d-dirty #2605
Call trace:
__pack+0x90/0x198 (P)
__pack+0x90/0x198 (L)
packing+0x78/0x98
ocelot_ifh_set_basic+0x260/0x368
ocelot_port_inject_frame+0xa8/0x250
felix_port_deferred_xmit+0x14c/0x258
kthread_worker_fn+0x134/0x350
kthread+0x114/0x138
The code path pertains to the ocelot switchdev driver and to the felix
secondary DSA tag protocol, ocelot-8021q. Here seen with ocelot-8021q.
The messenger (packing) is not really to blame, so fix the original
commit instead.
Fixes: e1b9e80236c5 ("net: mscc: ocelot: fix QoS class for injected packets with "ocelot-8021q"")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241212165546.879567-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
syzbot reported the following crash [1]
Issue came with the blamed commit. Instead of going through
all the iov components, we keep using the first one
and end up with a malformed skb.
[1]
kernel BUG at net/core/skbuff.c:2849 !
Oops: invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI
CPU: 0 UID: 0 PID: 6230 Comm: syz-executor132 Not tainted 6.13.0-rc1-syzkaller-00407-g96b6fcc0ee41 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 11/25/2024
RIP: 0010:__pskb_pull_tail+0x1568/0x1570 net/core/skbuff.c:2848
Code: 38 c1 0f 8c 32 f1 ff ff 4c 89 f7 e8 92 96 74 f8 e9 25 f1 ff ff e8 e8 ae 09 f8 48 8b 5c 24 08 e9 eb fb ff ff e8 d9 ae 09 f8 90 <0f> 0b 66 0f 1f 44 00 00 90 90 90 90 90 90 90 90 90 90 90 90 90 90
RSP: 0018:ffffc90004cbef30 EFLAGS: 00010293
RAX: ffffffff8995c347 RBX: 00000000fffffff2 RCX: ffff88802cf45a00
RDX: 0000000000000000 RSI: 00000000fffffff2 RDI: 0000000000000000
RBP: ffff88807df0c06a R08: ffffffff8995b084 R09: 1ffff1100fbe185c
R10: dffffc0000000000 R11: ffffed100fbe185d R12: ffff888076e85d50
R13: ffff888076e85c80 R14: ffff888076e85cf4 R15: ffff888076e85c80
FS: 00007f0dca6ea6c0(0000) GS:ffff8880b8600000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f0dca6ead58 CR3: 00000000119da000 CR4: 00000000003526f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
skb_cow_data+0x2da/0xcb0 net/core/skbuff.c:5284
tipc_aead_decrypt net/tipc/crypto.c:894 [inline]
tipc_crypto_rcv+0x402/0x24e0 net/tipc/crypto.c:1844
tipc_rcv+0x57e/0x12a0 net/tipc/node.c:2109
tipc_l2_rcv_msg+0x2bd/0x450 net/tipc/bearer.c:668
__netif_receive_skb_list_ptype net/core/dev.c:5720 [inline]
__netif_receive_skb_list_core+0x8b7/0x980 net/core/dev.c:5762
__netif_receive_skb_list net/core/dev.c:5814 [inline]
netif_receive_skb_list_internal+0xa51/0xe30 net/core/dev.c:5905
gro_normal_list include/net/gro.h:515 [inline]
napi_complete_done+0x2b5/0x870 net/core/dev.c:6256
napi_complete include/linux/netdevice.h:567 [inline]
tun_get_user+0x2ea0/0x4890 drivers/net/tun.c:1982
tun_chr_write_iter+0x10d/0x1f0 drivers/net/tun.c:2057
do_iter_readv_writev+0x600/0x880
vfs_writev+0x376/0xba0 fs/read_write.c:1050
do_writev+0x1b6/0x360 fs/read_write.c:1096
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Fixes: de4f5fed3f23 ("iov_iter: add iter_iovec() helper")
Reported-by: syzbot+4f66250f6663c0c1d67e@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/675b61aa.050a0220.599f4.00bb.GAE@google.com/T/#u
Cc: stable@vger.kernel.org
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://patch.msgid.link/20241212222247.724674-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When removing a netfront device directly after a suspend/resume cycle
it might happen that the queues have not been setup again, causing a
crash during the attempt to stop the queues another time.
Fix that by checking the queues are existing before trying to stop
them.
This is XSA-465 / CVE-2024-53240.
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Fixes: d50b7914fae0 ("xen-netfront: Fix NULL sring after live migration")
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
Commit 8d7ae22ae9f8 ("net: dsa: microchip: KSZ9477 register regmap
alignment to 32 bit boundaries") fixed an issue whereby regmap_reg_range
did not allow writes as 32 bit words to KSZ9477 PHY registers, this fix
for KSZ9896 is adapted from there as the same errata is present in
KSZ9896C as "Module 5: Certain PHY registers must be written as pairs
instead of singly" the explanation below is likewise taken from this
commit.
The commit provided code
to apply "Module 6: Certain PHY registers must be written as pairs instead
of singly" errata for KSZ9477 as this chip for certain PHY registers
(0xN120 to 0xN13F, N=1,2,3,4,5) must be accessed as 32 bit words instead
of 16 or 8 bit access.
Otherwise, adjacent registers (no matter if reserved or not) are
overwritten with 0x0.
Without this patch some registers (e.g. 0x113c or 0x1134) required for 32
bit access are out of valid regmap ranges.
As a result, following error is observed and KSZ9896 is not properly
configured:
ksz-switch spi1.0: can't rmw 32bit reg 0x113c: -EIO
ksz-switch spi1.0: can't rmw 32bit reg 0x1134: -EIO
ksz-switch spi1.0 lan1 (uninitialized): failed to connect to PHY: -EIO
ksz-switch spi1.0 lan1 (uninitialized): error -5 setting up PHY for tree 0, switch 0, port 0
The solution is to modify regmap_reg_range to allow accesses with 4 bytes
boundaries.
Fixes: 5c844d57aa78 ("net: dsa: microchip: fix writes to phy registers >= 0x10")
Signed-off-by: Jesse Van Gavere <jesse.vangavere@scioteq.com>
Link: https://patch.msgid.link/20241211092932.26881-1-jesse.vangavere@scioteq.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
MPIC.PIS must be set per phy interface type.
MPIC.LSC must be set per speed.
Do that strictly per datasheet, instead of hardcoding MPIC.PIS to GMII.
Fixes: 3590918b5d07 ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/20241211053012.368914-1-nikita.yoush@cogentembedded.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Similar to bonding driver, add NETIF_F_GSO_ENCAP_ALL to TEAM_VLAN_FEATURES
in order to support slave devices which propagate NETIF_F_GSO_UDP_TUNNEL &
NETIF_F_GSO_UDP_TUNNEL_CSUM as vlan_features.
Fixes: 3625920b62c3 ("teaming: fix vlan_features computing")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Cc: Ido Schimmel <idosch@idosch.org>
Cc: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://patch.msgid.link/20241210141245.327886-5-daniel@iogearbox.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Similarly as with bonding, fix the calculation of vlan_features to reuse
netdev_base_features() in order derive the set in the same way as
ndo_fix_features before iterating through the slave devices to refine the
feature set.
Fixes: 3625920b62c3 ("teaming: fix vlan_features computing")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Cc: Ido Schimmel <idosch@idosch.org>
Cc: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://patch.msgid.link/20241210141245.327886-4-daniel@iogearbox.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Drivers like mlx5 expose NIC's vlan_features such as
NETIF_F_GSO_UDP_TUNNEL & NETIF_F_GSO_UDP_TUNNEL_CSUM which are
later not propagated when the underlying devices are bonded and
a vlan device created on top of the bond.
Right now, the more cumbersome workaround for this is to create
the vlan on top of the mlx5 and then enslave the vlan devices
to a bond.
To fix this, add NETIF_F_GSO_ENCAP_ALL to BOND_VLAN_FEATURES
such that bond_compute_features() can probe and propagate the
vlan_features from the slave devices up to the vlan device.
Given the following bond:
# ethtool -i enp2s0f{0,1}np{0,1}
driver: mlx5_core
[...]
# ethtool -k enp2s0f0np0 | grep udp
tx-udp_tnl-segmentation: on
tx-udp_tnl-csum-segmentation: on
tx-udp-segmentation: on
rx-udp_tunnel-port-offload: on
rx-udp-gro-forwarding: off
# ethtool -k enp2s0f1np1 | grep udp
tx-udp_tnl-segmentation: on
tx-udp_tnl-csum-segmentation: on
tx-udp-segmentation: on
rx-udp_tunnel-port-offload: on
rx-udp-gro-forwarding: off
# ethtool -k bond0 | grep udp
tx-udp_tnl-segmentation: on
tx-udp_tnl-csum-segmentation: on
tx-udp-segmentation: on
rx-udp_tunnel-port-offload: off [fixed]
rx-udp-gro-forwarding: off
Before:
# ethtool -k bond0.100 | grep udp
tx-udp_tnl-segmentation: off [requested on]
tx-udp_tnl-csum-segmentation: off [requested on]
tx-udp-segmentation: on
rx-udp_tunnel-port-offload: off [fixed]
rx-udp-gro-forwarding: off
After:
# ethtool -k bond0.100 | grep udp
tx-udp_tnl-segmentation: on
tx-udp_tnl-csum-segmentation: on
tx-udp-segmentation: on
rx-udp_tunnel-port-offload: off [fixed]
rx-udp-gro-forwarding: off
Various users have run into this reporting performance issues when
configuring Cilium in vxlan tunneling mode and having the combination
of bond & vlan for the core devices connecting the Kubernetes cluster
to the outside world.
Fixes: a9b3ace44c7d ("bonding: fix vlan_features computing")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Cc: Ido Schimmel <idosch@idosch.org>
Cc: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://patch.msgid.link/20241210141245.327886-3-daniel@iogearbox.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
If a bonding device has slave devices, then the current logic to derive
the feature set for the master bond device is limited in that flags which
are fully supported by the underlying slave devices cannot be propagated
up to vlan devices which sit on top of bond devices. Instead, these get
blindly masked out via current NETIF_F_ALL_FOR_ALL logic.
vlan_features and mpls_features should reuse netdev_base_features() in
order derive the set in the same way as ndo_fix_features before iterating
through the slave devices to refine the feature set.
Fixes: a9b3ace44c7d ("bonding: fix vlan_features computing")
Fixes: 2e770b507ccd ("net: bonding: Inherit MPLS features from slave devices")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Cc: Ido Schimmel <idosch@idosch.org>
Cc: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://patch.msgid.link/20241210141245.327886-2-daniel@iogearbox.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Both bonding and team driver have logic to derive the base feature
flags before iterating over their slave devices to refine the set
via netdev_increment_features().
Add a small helper netdev_base_features() so this can be reused
instead of having it open-coded multiple times.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Cc: Ido Schimmel <idosch@idosch.org>
Cc: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20241210141245.327886-1-daniel@iogearbox.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
With this port schedule:
tc qdisc replace dev $send_if parent root handle 100 taprio \
num_tc 8 queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \
map 0 1 2 3 4 5 6 7 \
base-time 0 cycle-time 10000 \
sched-entry S 01 1250 \
sched-entry S 02 1250 \
sched-entry S 04 1250 \
sched-entry S 08 1250 \
sched-entry S 10 1250 \
sched-entry S 20 1250 \
sched-entry S 40 1250 \
sched-entry S 80 1250 \
flags 2
ptp4l would fail to take TX timestamps of Pdelay_Resp messages like this:
increasing tx_timestamp_timeout may correct this issue, but it is likely caused by a driver bug
ptp4l[4134.168]: port 2: send peer delay response failed
It turns out that the driver can't take their TX timestamps because it
can't transmit them in the first place. And there's nothing special
about the Pdelay_Resp packets - they're just regular 68 byte packets.
But with this taprio configuration, the switch would refuse to send even
the ETH_ZLEN minimum packet size.
This should have definitely not been the case. When applying the taprio
config, the driver prints:
mscc_felix 0000:00:00.5: port 0 tc 0 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 1 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 2 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 3 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 4 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 5 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 6 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 7 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 132 octets including FCS
and thus, everything under 132 bytes - ETH_FCS_LEN should have been sent
without problems. Yet it's not.
For the forwarding path, the configuration is fine, yet packets injected
from Linux get stuck with this schedule no matter what.
The first hint that the static guard bands are the cause of the problem
is that reverting Michael Walle's commit 297c4de6f780 ("net: dsa: felix:
re-enable TAS guard band mode") made things work. It must be that the
guard bands are calculated incorrectly.
I remembered that there is a magic constant in the driver, set to 33 ns
for no logical reason other than experimentation, which says "never let
the static guard bands get so large as to leave less than this amount of
remaining space in the time slot, because the queue system will refuse
to schedule packets otherwise, and they will get stuck". I had a hunch
that my previous experimentally-determined value was only good for
packets coming from the forwarding path, and that the CPU injection path
needed more.
I came to the new value of 35 ns through binary search, after seeing
that with 544 ns (the bit time required to send the Pdelay_Resp packet
at gigabit) it works. Again, this is purely experimental, there's no
logic and the manual doesn't say anything.
The new driver prints for this schedule look like this:
mscc_felix 0000:00:00.5: port 0 tc 0 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 1 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 2 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 3 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 4 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 5 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 6 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
mscc_felix 0000:00:00.5: port 0 tc 7 min gate length 1250 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 131 octets including FCS
So yes, the maximum MTU is now even smaller by 1 byte than before.
This is maybe counter-intuitive, but makes more sense with a diagram of
one time slot.
Before:
Gate open Gate close
| |
v 1250 ns total time slot duration v
<---------------------------------------------------->
<----><---------------------------------------------->
33 ns 1217 ns static guard band
useful
Gate open Gate close
| |
v 1250 ns total time slot duration v
<---------------------------------------------------->
<-----><--------------------------------------------->
35 ns 1215 ns static guard band
useful
The static guard band implemented by this switch hardware directly
determines the maximum allowable MTU for that traffic class. The larger
it is, the earlier the switch will stop scheduling frames for
transmission, because otherwise they might overrun the gate close time
(and avoiding that is the entire purpose of Michael's patch).
So, we now have guard bands smaller by 2 ns, thus, in this particular
case, we lose a byte of the maximum MTU.
Fixes: 11afdc6526de ("net: dsa: felix: tc-taprio intervals smaller than MTU should send at least one packet")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Link: https://patch.msgid.link/20241210132640.3426788-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add the following Telit FE910C04 compositions:
0x10c0: rmnet + tty (AT/NMEA) + tty (AT) + tty (diag)
T: Bus=02 Lev=01 Prnt=03 Port=06 Cnt=01 Dev#= 13 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10c0 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FE910
S: SerialNumber=f71b8b32
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
0x10c4: rmnet + tty (AT) + tty (AT) + tty (diag)
T: Bus=02 Lev=01 Prnt=03 Port=06 Cnt=01 Dev#= 14 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10c4 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FE910
S: SerialNumber=f71b8b32
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
0x10c8: rmnet + tty (AT) + tty (diag) + DPL (data packet logging) + adb
T: Bus=02 Lev=01 Prnt=03 Port=06 Cnt=01 Dev#= 17 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10c8 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FE910
S: SerialNumber=f71b8b32
C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none)
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Link: https://patch.msgid.link/20241209151821.3688829-1-dnlplm@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
gc->irq_contexts is not freeded if one of the later operations
fail.
Suggested-by: Michael Kelley <mhklinux@outlook.com>
Fixes: 8afefc361209 ("net: mana: Assigning IRQ affinity on HT cores")
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Saurabh Sengar <ssengar@linux.microsoft.com>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Link: https://patch.msgid.link/20241209175751.287738-3-mlevitsk@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 8afefc361209 ("net: mana: Assigning IRQ affinity on HT cores")
added memory allocation in mana_gd_setup_irqs of 'irqs' but the code
doesn't free this temporary array in the success path.
This was caught by kmemleak.
Fixes: 8afefc361209 ("net: mana: Assigning IRQ affinity on HT cores")
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Saurabh Sengar <ssengar@linux.microsoft.com>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Link: https://patch.msgid.link/20241209175751.287738-2-mlevitsk@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently the stop routine of rswitch driver does not immediately
prevent hardware from continuing to update descriptors and requesting
interrupts.
It can happen that when rswitch_stop() executes the masking of
interrupts from the queues of the port being closed, napi poll for
that port is already scheduled or running on a different CPU. When
execution of this napi poll completes, it will unmask the interrupts.
And unmasked interrupt can fire after rswitch_stop() returns from
napi_disable() call. Then, the handler won't mask it, because
napi_schedule_prep() will return false, and interrupt storm will
happen.
This can't be fixed by making rswitch_stop() call napi_disable() before
masking interrupts. In this case, the interrupt storm will happen if
interrupt fires between napi_disable() and masking.
Fix this by checking for priv->opened_ports bit when unmasking
interrupts after napi poll. For that to be consistent, move
priv->opened_ports changes into spinlock-protected areas, and reorder
other operations in rswitch_open() and rswitch_stop() accordingly.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Fixes: 3590918b5d07 ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Link: https://patch.msgid.link/20241209113204.175015-1-nikita.yoush@cogentembedded.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The device tree node saved in the rswitch_device structure is used at
several driver locations. So passing this node to of_node_put() after
the first use is wrong.
Move of_node_put() for this node to exit paths.
Fixes: b46f1e579329 ("net: renesas: rswitch: Simplify struct phy * handling")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://patch.msgid.link/20241208095004.69468-5-nikita.yoush@cogentembedded.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If error path is taken while filling descriptor for a frame, skb
pointer is left in the entry. Later, on the ring entry reuse, the
same entry could be used as a part of a multi-descriptor frame,
and skb for that new frame could be stored in a different entry.
Then, the stale pointer will reach the completion routine, and passed
to the release operation.
Fix that by clearing the saved skb pointer at the error path.
Fixes: d2c96b9d5f83 ("net: rswitch: Add jumbo frames handling for TX")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://patch.msgid.link/20241208095004.69468-4-nikita.yoush@cogentembedded.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If hardware is already transmitting, it can start handling the
descriptor being written to immediately after it observes updated DT
field, before the queue is kicked by a write to GWTRC.
If the start_xmit() execution is preempted at unfortunate moment, this
transmission can complete, and interrupt handled, before gq->cur gets
updated. With the current implementation of completion, this will cause
the last entry not completed.
Fix that by changing completion loop to check DT values directly, instead
of depending on gq->cur.
Fixes: 3590918b5d07 ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://patch.msgid.link/20241208095004.69468-3-nikita.yoush@cogentembedded.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When sending frame split into multiple descriptors, hardware processes
descriptors one by one, including writing back DT values. The first
descriptor could be already marked as completed when processing of
next descriptors for the same frame is still in progress.
Although only the last descriptor is configured to generate interrupt,
completion of the first descriptor could be noticed by the driver when
handling interrupt for the previous frame.
Currently, driver stores skb in the entry that corresponds to the first
descriptor. This results into skb could be unmapped and freed when
hardware did not complete the send yet. This opens a window for
corrupting the data being sent.
Fix this by saving skb in the entry that corresponds to the last
descriptor used to send the frame.
Fixes: d2c96b9d5f83 ("net: rswitch: Add jumbo frames handling for TX")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://patch.msgid.link/20241208095004.69468-2-nikita.yoush@cogentembedded.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Johannes Berg says:
====================
A small set of fixes:
- avoid CSA warnings during link removal
(by changing link bitmap after remove)
- fix # of spatial streams initialisation
- fix queues getting stuck in some CSA cases
and resume failures
- fix interface address when switching monitor mode
- fix MBSS change flags 32-bit stack corruption
- more UBSAN __counted_by "fixes" ...
- fix link ID netlink validation
* tag 'wireless-2024-12-10' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: cfg80211: sme: init n_channels before channels[] access
wifi: mac80211: fix station NSS capability initialization order
wifi: mac80211: fix vif addr when switching from monitor to station
wifi: mac80211: fix a queue stall in certain cases of CSA
wifi: mac80211: wake the queues in case of failure in resume
wifi: cfg80211: clear link ID from bitmap during link delete after clean up
wifi: mac80211: init cnt before accessing elem in ieee80211_copy_mbssid_beacon
wifi: mac80211: fix mbss changed flags corruption on 32 bit systems
wifi: nl80211: fix NL80211_ATTR_MLO_LINK_ID off-by-one
====================
Link: https://patch.msgid.link/20241210130145.28618-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The 5760X (P7) chip's HW GRO/LRO interface is very similar to that of
the previous generation (5750X or P5). However, the aggregation ID
fields in the completion structures on P7 have been redefined from
16 bits to 12 bits. The freed up 4 bits are redefined for part of the
metadata such as the VLAN ID. The aggregation ID mask was not modified
when adding support for P7 chips. Including the extra 4 bits for the
aggregation ID can potentially cause the driver to store or fetch the
packet header of GRO/LRO packets in the wrong TPA buffer. It may hit
the BUG() condition in __skb_pull() because the SKB contains no valid
packet header:
kernel BUG at include/linux/skbuff.h:2766!
Oops: invalid opcode: 0000 1 PREEMPT SMP NOPTI
CPU: 4 UID: 0 PID: 0 Comm: swapper/4 Kdump: loaded Tainted: G OE 6.12.0-rc2+ #7
Tainted: [O]=OOT_MODULE, [E]=UNSIGNED_MODULE
Hardware name: Dell Inc. PowerEdge R760/0VRV9X, BIOS 1.0.1 12/27/2022
RIP: 0010:eth_type_trans+0xda/0x140
Code: 80 00 00 00 eb c1 8b 47 70 2b 47 74 48 8b 97 d0 00 00 00 83 f8 01 7e 1b 48 85 d2 74 06 66 83 3a ff 74 09 b8 00 04 00 00 eb a5 <0f> 0b b8 00 01 00 00 eb 9c 48 85 ff 74 eb 31 f6 b9 02 00 00 00 48
RSP: 0018:ff615003803fcc28 EFLAGS: 00010283
RAX: 00000000000022d2 RBX: 0000000000000003 RCX: ff2e8c25da334040
RDX: 0000000000000040 RSI: ff2e8c25c1ce8000 RDI: ff2e8c25869f9000
RBP: ff2e8c258c31c000 R08: ff2e8c25da334000 R09: 0000000000000001
R10: ff2e8c25da3342c0 R11: ff2e8c25c1ce89c0 R12: ff2e8c258e0990b0
R13: ff2e8c25bb120000 R14: ff2e8c25c1ce89c0 R15: ff2e8c25869f9000
FS: 0000000000000000(0000) GS:ff2e8c34be300000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055f05317e4c8 CR3: 000000108bac6006 CR4: 0000000000773ef0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe07f0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
<IRQ>
? die+0x33/0x90
? do_trap+0xd9/0x100
? eth_type_trans+0xda/0x140
? do_error_trap+0x65/0x80
? eth_type_trans+0xda/0x140
? exc_invalid_op+0x4e/0x70
? eth_type_trans+0xda/0x140
? asm_exc_invalid_op+0x16/0x20
? eth_type_trans+0xda/0x140
bnxt_tpa_end+0x10b/0x6b0 [bnxt_en]
? bnxt_tpa_start+0x195/0x320 [bnxt_en]
bnxt_rx_pkt+0x902/0xd90 [bnxt_en]
? __bnxt_tx_int.constprop.0+0x89/0x300 [bnxt_en]
? kmem_cache_free+0x343/0x440
? __bnxt_tx_int.constprop.0+0x24f/0x300 [bnxt_en]
__bnxt_poll_work+0x193/0x370 [bnxt_en]
bnxt_poll_p5+0x9a/0x300 [bnxt_en]
? try_to_wake_up+0x209/0x670
__napi_poll+0x29/0x1b0
Fix it by redefining the aggregation ID mask for P5_PLUS chips to be
12 bits. This will work because the maximum aggregation ID is less
than 4096 on all P5_PLUS chips.
Fixes: 13d2d3d381ee ("bnxt_en: Add new P7 hardware interface definitions")
Reviewed-by: Damodharam Ammepalli <damodharam.ammepalli@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241209015448.1937766-1-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
virtnet_sq_bind_xsk_pool() flushes tx skbs and then resets tx queue, so
DQL counters need to be reset when flushing has actually occurred, Add
virtnet_sq_free_unused_buf_done() as a callback for virtqueue_resize()
to handle this.
Fixes: 21a4e3ce6dc7 ("virtio_net: xsk: bind/unbind xsk for tx")
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When virtqueue_reset() has actually recycled all unused buffers,
additional work may be required in some cases. Relying solely on its
return status is fragile, so introduce a new function argument
'recycle_done', which is invoked when it really occurs.
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
virtnet_tx_resize() flushes remaining tx skbs, requiring DQL counters to
be reset when flushing has actually occurred. Add
virtnet_sq_free_unused_buf_done() as a callback for virtqueue_reset() to
handle this.
Fixes: c8bd1f7f3e61 ("virtio_net: add support for Byte Queue Limits")
Cc: <stable@vger.kernel.org> # v6.11+
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When virtqueue_resize() has actually recycled all unused buffers,
additional work may be required in some cases. Relying solely on its
return status is fragile, so introduce a new function argument
'recycle_done', which is invoked when the recycle really occurs.
Cc: <stable@vger.kernel.org> # v6.11+
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
