aboutsummaryrefslogtreecommitdiff
path: root/drivers/fpga
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/fpga')
-rw-r--r--drivers/fpga/Kconfig28
-rw-r--r--drivers/fpga/Makefile2
-rw-r--r--drivers/fpga/dfl-afu-error.c10
-rw-r--r--drivers/fpga/dfl-afu-main.c35
-rw-r--r--drivers/fpga/dfl-afu.h2
-rw-r--r--drivers/fpga/dfl-fme-perf.c6
-rw-r--r--drivers/fpga/dfl-n3000-nios.c588
-rw-r--r--drivers/fpga/dfl-pci.c183
-rw-r--r--drivers/fpga/dfl.c4
-rw-r--r--drivers/fpga/dfl.h85
-rw-r--r--drivers/fpga/fpga-bridge.c4
-rw-r--r--drivers/fpga/xilinx-pr-decoupler.c45
-rw-r--r--drivers/fpga/xilinx-spi.c24
13 files changed, 836 insertions, 180 deletions
diff --git a/drivers/fpga/Kconfig b/drivers/fpga/Kconfig
index 5645226ca3ce..33e15058d0dc 100644
--- a/drivers/fpga/Kconfig
+++ b/drivers/fpga/Kconfig
@@ -14,13 +14,13 @@ if FPGA
config FPGA_MGR_SOCFPGA
tristate "Altera SOCFPGA FPGA Manager"
- depends on ARCH_SOCFPGA || COMPILE_TEST
+ depends on ARCH_INTEL_SOCFPGA || COMPILE_TEST
help
FPGA manager driver support for Altera SOCFPGA.
config FPGA_MGR_SOCFPGA_A10
tristate "Altera SoCFPGA Arria10"
- depends on ARCH_SOCFPGA || COMPILE_TEST
+ depends on ARCH_INTEL_SOCFPGA || COMPILE_TEST
select REGMAP_MMIO
help
FPGA manager driver support for Altera Arria10 SoCFPGA.
@@ -60,7 +60,7 @@ config FPGA_MGR_ZYNQ_FPGA
config FPGA_MGR_STRATIX10_SOC
tristate "Intel Stratix10 SoC FPGA Manager"
- depends on (ARCH_STRATIX10 && INTEL_STRATIX10_SERVICE)
+ depends on (ARCH_INTEL_SOCFPGA && INTEL_STRATIX10_SERVICE)
help
FPGA manager driver support for the Intel Stratix10 SoC.
@@ -99,7 +99,7 @@ config FPGA_BRIDGE
config SOCFPGA_FPGA_BRIDGE
tristate "Altera SoCFPGA FPGA Bridges"
- depends on ARCH_SOCFPGA && FPGA_BRIDGE
+ depends on ARCH_INTEL_SOCFPGA && FPGA_BRIDGE
help
Say Y to enable drivers for FPGA bridges for Altera SOCFPGA
devices.
@@ -118,10 +118,17 @@ config XILINX_PR_DECOUPLER
depends on FPGA_BRIDGE
depends on HAS_IOMEM
help
- Say Y to enable drivers for Xilinx LogiCORE PR Decoupler.
+ Say Y to enable drivers for Xilinx LogiCORE PR Decoupler
+ or Xilinx Dynamic Function eXchnage AIX Shutdown Manager.
The PR Decoupler exists in the FPGA fabric to isolate one
region of the FPGA from the busses while that region is
being reprogrammed during partial reconfig.
+ The Dynamic Function eXchange AXI shutdown manager prevents
+ AXI traffic from passing through the bridge. The controller
+ safely handles AXI4MM and AXI4-Lite interfaces on a
+ Reconfigurable Partition when it is undergoing dynamic
+ reconfiguration, preventing the system deadlock that can
+ occur if AXI transactions are interrupted by DFX.
config FPGA_REGION
tristate "FPGA Region"
@@ -192,6 +199,17 @@ config FPGA_DFL_AFU
to the FPGA infrastructure via a Port. There may be more than one
Port/AFU per DFL based FPGA device.
+config FPGA_DFL_NIOS_INTEL_PAC_N3000
+ tristate "FPGA DFL NIOS Driver for Intel PAC N3000"
+ depends on FPGA_DFL
+ select REGMAP
+ help
+ This is the driver for the N3000 Nios private feature on Intel
+ PAC (Programmable Acceleration Card) N3000. It communicates
+ with the embedded Nios processor to configure the retimers on
+ the card. It also instantiates the SPI master (spi-altera) for
+ the card's BMC (Board Management Controller).
+
config FPGA_DFL_PCI
tristate "FPGA DFL PCIe Device Driver"
depends on PCI && FPGA_DFL
diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile
index d8e21dfc6778..18dc9885883a 100644
--- a/drivers/fpga/Makefile
+++ b/drivers/fpga/Makefile
@@ -44,5 +44,7 @@ dfl-fme-objs += dfl-fme-perf.o
dfl-afu-objs := dfl-afu-main.o dfl-afu-region.o dfl-afu-dma-region.o
dfl-afu-objs += dfl-afu-error.o
+obj-$(CONFIG_FPGA_DFL_NIOS_INTEL_PAC_N3000) += dfl-n3000-nios.o
+
# Drivers for FPGAs which implement DFL
obj-$(CONFIG_FPGA_DFL_PCI) += dfl-pci.o
diff --git a/drivers/fpga/dfl-afu-error.c b/drivers/fpga/dfl-afu-error.c
index c4691187cca9..ab7be6217368 100644
--- a/drivers/fpga/dfl-afu-error.c
+++ b/drivers/fpga/dfl-afu-error.c
@@ -52,7 +52,7 @@ static int afu_port_err_clear(struct device *dev, u64 err)
struct dfl_feature_platform_data *pdata = dev_get_platdata(dev);
struct platform_device *pdev = to_platform_device(dev);
void __iomem *base_err, *base_hdr;
- int ret = -EBUSY;
+ int enable_ret = 0, ret = -EBUSY;
u64 v;
base_err = dfl_get_feature_ioaddr_by_id(dev, PORT_FEATURE_ID_ERROR);
@@ -96,18 +96,20 @@ static int afu_port_err_clear(struct device *dev, u64 err)
v = readq(base_err + PORT_FIRST_ERROR);
writeq(v, base_err + PORT_FIRST_ERROR);
} else {
+ dev_warn(dev, "%s: received 0x%llx, expected 0x%llx\n",
+ __func__, v, err);
ret = -EINVAL;
}
/* Clear mask */
__afu_port_err_mask(dev, false);
- /* Enable the Port by clear the reset */
- __afu_port_enable(pdev);
+ /* Enable the Port by clearing the reset */
+ enable_ret = __afu_port_enable(pdev);
done:
mutex_unlock(&pdata->lock);
- return ret;
+ return enable_ret ? enable_ret : ret;
}
static ssize_t errors_show(struct device *dev, struct device_attribute *attr,
diff --git a/drivers/fpga/dfl-afu-main.c b/drivers/fpga/dfl-afu-main.c
index 753cda4b2568..7f621e96d3b8 100644
--- a/drivers/fpga/dfl-afu-main.c
+++ b/drivers/fpga/dfl-afu-main.c
@@ -21,6 +21,9 @@
#include "dfl-afu.h"
+#define RST_POLL_INVL 10 /* us */
+#define RST_POLL_TIMEOUT 1000 /* us */
+
/**
* __afu_port_enable - enable a port by clear reset
* @pdev: port platform device.
@@ -32,7 +35,7 @@
*
* The caller needs to hold lock for protection.
*/
-void __afu_port_enable(struct platform_device *pdev)
+int __afu_port_enable(struct platform_device *pdev)
{
struct dfl_feature_platform_data *pdata = dev_get_platdata(&pdev->dev);
void __iomem *base;
@@ -41,7 +44,7 @@ void __afu_port_enable(struct platform_device *pdev)
WARN_ON(!pdata->disable_count);
if (--pdata->disable_count != 0)
- return;
+ return 0;
base = dfl_get_feature_ioaddr_by_id(&pdev->dev, PORT_FEATURE_ID_HEADER);
@@ -49,10 +52,20 @@ void __afu_port_enable(struct platform_device *pdev)
v = readq(base + PORT_HDR_CTRL);
v &= ~PORT_CTRL_SFTRST;
writeq(v, base + PORT_HDR_CTRL);
-}
-#define RST_POLL_INVL 10 /* us */
-#define RST_POLL_TIMEOUT 1000 /* us */
+ /*
+ * HW clears the ack bit to indicate that the port is fully out
+ * of reset.
+ */
+ if (readq_poll_timeout(base + PORT_HDR_CTRL, v,
+ !(v & PORT_CTRL_SFTRST_ACK),
+ RST_POLL_INVL, RST_POLL_TIMEOUT)) {
+ dev_err(&pdev->dev, "timeout, failure to enable device\n");
+ return -ETIMEDOUT;
+ }
+
+ return 0;
+}
/**
* __afu_port_disable - disable a port by hold reset
@@ -86,7 +99,7 @@ int __afu_port_disable(struct platform_device *pdev)
if (readq_poll_timeout(base + PORT_HDR_CTRL, v,
v & PORT_CTRL_SFTRST_ACK,
RST_POLL_INVL, RST_POLL_TIMEOUT)) {
- dev_err(&pdev->dev, "timeout, fail to reset device\n");
+ dev_err(&pdev->dev, "timeout, failure to disable device\n");
return -ETIMEDOUT;
}
@@ -110,10 +123,10 @@ static int __port_reset(struct platform_device *pdev)
int ret;
ret = __afu_port_disable(pdev);
- if (!ret)
- __afu_port_enable(pdev);
+ if (ret)
+ return ret;
- return ret;
+ return __afu_port_enable(pdev);
}
static int port_reset(struct platform_device *pdev)
@@ -872,11 +885,11 @@ static int afu_dev_destroy(struct platform_device *pdev)
static int port_enable_set(struct platform_device *pdev, bool enable)
{
struct dfl_feature_platform_data *pdata = dev_get_platdata(&pdev->dev);
- int ret = 0;
+ int ret;
mutex_lock(&pdata->lock);
if (enable)
- __afu_port_enable(pdev);
+ ret = __afu_port_enable(pdev);
else
ret = __afu_port_disable(pdev);
mutex_unlock(&pdata->lock);
diff --git a/drivers/fpga/dfl-afu.h b/drivers/fpga/dfl-afu.h
index 576e94960086..e5020e2b1f3d 100644
--- a/drivers/fpga/dfl-afu.h
+++ b/drivers/fpga/dfl-afu.h
@@ -80,7 +80,7 @@ struct dfl_afu {
};
/* hold pdata->lock when call __afu_port_enable/disable */
-void __afu_port_enable(struct platform_device *pdev);
+int __afu_port_enable(struct platform_device *pdev);
int __afu_port_disable(struct platform_device *pdev);
void afu_mmio_region_init(struct dfl_feature_platform_data *pdata);
diff --git a/drivers/fpga/dfl-fme-perf.c b/drivers/fpga/dfl-fme-perf.c
index 531266287eee..4299145ef347 100644
--- a/drivers/fpga/dfl-fme-perf.c
+++ b/drivers/fpga/dfl-fme-perf.c
@@ -192,7 +192,7 @@ static struct attribute *fme_perf_cpumask_attrs[] = {
NULL,
};
-static struct attribute_group fme_perf_cpumask_group = {
+static const struct attribute_group fme_perf_cpumask_group = {
.attrs = fme_perf_cpumask_attrs,
};
@@ -225,7 +225,7 @@ static struct attribute *fme_perf_format_attrs[] = {
NULL,
};
-static struct attribute_group fme_perf_format_group = {
+static const struct attribute_group fme_perf_format_group = {
.name = "format",
.attrs = fme_perf_format_attrs,
};
@@ -239,7 +239,7 @@ static struct attribute *fme_perf_events_attrs_empty[] = {
NULL,
};
-static struct attribute_group fme_perf_events_group = {
+static const struct attribute_group fme_perf_events_group = {
.name = "events",
.attrs = fme_perf_events_attrs_empty,
};
diff --git a/drivers/fpga/dfl-n3000-nios.c b/drivers/fpga/dfl-n3000-nios.c
new file mode 100644
index 000000000000..7a95366f6516
--- /dev/null
+++ b/drivers/fpga/dfl-n3000-nios.c
@@ -0,0 +1,588 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * DFL device driver for Nios private feature on Intel PAC (Programmable
+ * Acceleration Card) N3000
+ *
+ * Copyright (C) 2019-2020 Intel Corporation, Inc.
+ *
+ * Authors:
+ * Wu Hao <hao.wu@intel.com>
+ * Xu Yilun <yilun.xu@intel.com>
+ */
+#include <linux/bitfield.h>
+#include <linux/dfl.h>
+#include <linux/errno.h>
+#include <linux/io.h>
+#include <linux/io-64-nonatomic-lo-hi.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/stddef.h>
+#include <linux/spi/altera.h>
+#include <linux/spi/spi.h>
+#include <linux/types.h>
+
+/*
+ * N3000 Nios private feature registers, named as NIOS_SPI_XX on spec.
+ * NS is the abbreviation of NIOS_SPI.
+ */
+#define N3000_NS_PARAM 0x8
+#define N3000_NS_PARAM_SHIFT_MODE_MSK BIT_ULL(1)
+#define N3000_NS_PARAM_SHIFT_MODE_MSB 0
+#define N3000_NS_PARAM_SHIFT_MODE_LSB 1
+#define N3000_NS_PARAM_DATA_WIDTH GENMASK_ULL(7, 2)
+#define N3000_NS_PARAM_NUM_CS GENMASK_ULL(13, 8)
+#define N3000_NS_PARAM_CLK_POL BIT_ULL(14)
+#define N3000_NS_PARAM_CLK_PHASE BIT_ULL(15)
+#define N3000_NS_PARAM_PERIPHERAL_ID GENMASK_ULL(47, 32)
+
+#define N3000_NS_CTRL 0x10
+#define N3000_NS_CTRL_WR_DATA GENMASK_ULL(31, 0)
+#define N3000_NS_CTRL_ADDR GENMASK_ULL(44, 32)
+#define N3000_NS_CTRL_CMD_MSK GENMASK_ULL(63, 62)
+#define N3000_NS_CTRL_CMD_NOP 0
+#define N3000_NS_CTRL_CMD_RD 1
+#define N3000_NS_CTRL_CMD_WR 2
+
+#define N3000_NS_STAT 0x18
+#define N3000_NS_STAT_RD_DATA GENMASK_ULL(31, 0)
+#define N3000_NS_STAT_RW_VAL BIT_ULL(32)
+
+/* Nios handshake registers, indirect access */
+#define N3000_NIOS_INIT 0x1000
+#define N3000_NIOS_INIT_DONE BIT(0)
+#define N3000_NIOS_INIT_START BIT(1)
+/* Mode for retimer A, link 0, the same below */
+#define N3000_NIOS_INIT_REQ_FEC_MODE_A0_MSK GENMASK(9, 8)
+#define N3000_NIOS_INIT_REQ_FEC_MODE_A1_MSK GENMASK(11, 10)
+#define N3000_NIOS_INIT_REQ_FEC_MODE_A2_MSK GENMASK(13, 12)
+#define N3000_NIOS_INIT_REQ_FEC_MODE_A3_MSK GENMASK(15, 14)
+#define N3000_NIOS_INIT_REQ_FEC_MODE_B0_MSK GENMASK(17, 16)
+#define N3000_NIOS_INIT_REQ_FEC_MODE_B1_MSK GENMASK(19, 18)
+#define N3000_NIOS_INIT_REQ_FEC_MODE_B2_MSK GENMASK(21, 20)
+#define N3000_NIOS_INIT_REQ_FEC_MODE_B3_MSK GENMASK(23, 22)
+#define N3000_NIOS_INIT_REQ_FEC_MODE_NO 0x0
+#define N3000_NIOS_INIT_REQ_FEC_MODE_KR 0x1
+#define N3000_NIOS_INIT_REQ_FEC_MODE_RS 0x2
+
+#define N3000_NIOS_FW_VERSION 0x1004
+#define N3000_NIOS_FW_VERSION_PATCH GENMASK(23, 20)
+#define N3000_NIOS_FW_VERSION_MINOR GENMASK(27, 24)
+#define N3000_NIOS_FW_VERSION_MAJOR GENMASK(31, 28)
+
+/* The retimers we use on Intel PAC N3000 is Parkvale, abbreviated to PKVL */
+#define N3000_NIOS_PKVL_A_MODE_STS 0x1020
+#define N3000_NIOS_PKVL_B_MODE_STS 0x1024
+#define N3000_NIOS_PKVL_MODE_STS_GROUP_MSK GENMASK(15, 8)
+#define N3000_NIOS_PKVL_MODE_STS_GROUP_OK 0x0
+#define N3000_NIOS_PKVL_MODE_STS_ID_MSK GENMASK(7, 0)
+/* When GROUP MASK field == GROUP_OK */
+#define N3000_NIOS_PKVL_MODE_ID_RESET 0x0
+#define N3000_NIOS_PKVL_MODE_ID_4X10G 0x1
+#define N3000_NIOS_PKVL_MODE_ID_4X25G 0x2
+#define N3000_NIOS_PKVL_MODE_ID_2X25G 0x3
+#define N3000_NIOS_PKVL_MODE_ID_2X25G_2X10G 0x4
+#define N3000_NIOS_PKVL_MODE_ID_1X25G 0x5
+
+#define N3000_NIOS_REGBUS_RETRY_COUNT 10000 /* loop count */
+
+#define N3000_NIOS_INIT_TIMEOUT 10000000 /* usec */
+#define N3000_NIOS_INIT_TIME_INTV 100000 /* usec */
+
+#define N3000_NIOS_INIT_REQ_FEC_MODE_MSK_ALL \
+ (N3000_NIOS_INIT_REQ_FEC_MODE_A0_MSK | \
+ N3000_NIOS_INIT_REQ_FEC_MODE_A1_MSK | \
+ N3000_NIOS_INIT_REQ_FEC_MODE_A2_MSK | \
+ N3000_NIOS_INIT_REQ_FEC_MODE_A3_MSK | \
+ N3000_NIOS_INIT_REQ_FEC_MODE_B0_MSK | \
+ N3000_NIOS_INIT_REQ_FEC_MODE_B1_MSK | \
+ N3000_NIOS_INIT_REQ_FEC_MODE_B2_MSK | \
+ N3000_NIOS_INIT_REQ_FEC_MODE_B3_MSK)
+
+#define N3000_NIOS_INIT_REQ_FEC_MODE_NO_ALL \
+ (FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_A0_MSK, \
+ N3000_NIOS_INIT_REQ_FEC_MODE_NO) | \
+ FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_A1_MSK, \
+ N3000_NIOS_INIT_REQ_FEC_MODE_NO) | \
+ FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_A2_MSK, \
+ N3000_NIOS_INIT_REQ_FEC_MODE_NO) | \
+ FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_A3_MSK, \
+ N3000_NIOS_INIT_REQ_FEC_MODE_NO) | \
+ FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_B0_MSK, \
+ N3000_NIOS_INIT_REQ_FEC_MODE_NO) | \
+ FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_B1_MSK, \
+ N3000_NIOS_INIT_REQ_FEC_MODE_NO) | \
+ FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_B2_MSK, \
+ N3000_NIOS_INIT_REQ_FEC_MODE_NO) | \
+ FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_B3_MSK, \
+ N3000_NIOS_INIT_REQ_FEC_MODE_NO))
+
+#define N3000_NIOS_INIT_REQ_FEC_MODE_KR_ALL \
+ (FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_A0_MSK, \
+ N3000_NIOS_INIT_REQ_FEC_MODE_KR) | \
+ FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_A1_MSK, \
+ N3000_NIOS_INIT_REQ_FEC_MODE_KR) | \
+ FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_A2_MSK, \
+ N3000_NIOS_INIT_REQ_FEC_MODE_KR) | \
+ FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_A3_MSK, \
+ N3000_NIOS_INIT_REQ_FEC_MODE_KR) | \
+ FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_B0_MSK, \
+ N3000_NIOS_INIT_REQ_FEC_MODE_KR) | \
+ FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_B1_MSK, \
+ N3000_NIOS_INIT_REQ_FEC_MODE_KR) | \
+ FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_B2_MSK, \
+ N3000_NIOS_INIT_REQ_FEC_MODE_KR) | \
+ FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_B3_MSK, \
+ N3000_NIOS_INIT_REQ_FEC_MODE_KR))
+
+#define N3000_NIOS_INIT_REQ_FEC_MODE_RS_ALL \
+ (FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_A0_MSK, \
+ N3000_NIOS_INIT_REQ_FEC_MODE_RS) | \
+ FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_A1_MSK, \
+ N3000_NIOS_INIT_REQ_FEC_MODE_RS) | \
+ FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_A2_MSK, \
+ N3000_NIOS_INIT_REQ_FEC_MODE_RS) | \
+ FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_A3_MSK, \
+ N3000_NIOS_INIT_REQ_FEC_MODE_RS) | \
+ FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_B0_MSK, \
+ N3000_NIOS_INIT_REQ_FEC_MODE_RS) | \
+ FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_B1_MSK, \
+ N3000_NIOS_INIT_REQ_FEC_MODE_RS) | \
+ FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_B2_MSK, \
+ N3000_NIOS_INIT_REQ_FEC_MODE_RS) | \
+ FIELD_PREP(N3000_NIOS_INIT_REQ_FEC_MODE_B3_MSK, \
+ N3000_NIOS_INIT_REQ_FEC_MODE_RS))
+
+struct n3000_nios {
+ void __iomem *base;
+ struct regmap *regmap;
+ struct device *dev;
+ struct platform_device *altera_spi;
+};
+
+static ssize_t nios_fw_version_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct n3000_nios *nn = dev_get_drvdata(dev);
+ unsigned int val;
+ int ret;
+
+ ret = regmap_read(nn->regmap, N3000_NIOS_FW_VERSION, &val);
+ if (ret)
+ return ret;
+
+ return sysfs_emit(buf, "%x.%x.%x\n",
+ (u8)FIELD_GET(N3000_NIOS_FW_VERSION_MAJOR, val),
+ (u8)FIELD_GET(N3000_NIOS_FW_VERSION_MINOR, val),
+ (u8)FIELD_GET(N3000_NIOS_FW_VERSION_PATCH, val));
+}
+static DEVICE_ATTR_RO(nios_fw_version);
+
+#define IS_MODE_STATUS_OK(mode_stat) \
+ (FIELD_GET(N3000_NIOS_PKVL_MODE_STS_GROUP_MSK, (mode_stat)) == \
+ N3000_NIOS_PKVL_MODE_STS_GROUP_OK)
+
+#define IS_RETIMER_FEC_SUPPORTED(retimer_mode) \
+ ((retimer_mode) != N3000_NIOS_PKVL_MODE_ID_RESET && \
+ (retimer_mode) != N3000_NIOS_PKVL_MODE_ID_4X10G)
+
+static int get_retimer_mode(struct n3000_nios *nn, unsigned int mode_stat_reg,
+ unsigned int *retimer_mode)
+{
+ unsigned int val;
+ int ret;
+
+ ret = regmap_read(nn->regmap, mode_stat_reg, &val);
+ if (ret)
+ return ret;
+
+ if (!IS_MODE_STATUS_OK(val))
+ return -EFAULT;
+
+ *retimer_mode = FIELD_GET(N3000_NIOS_PKVL_MODE_STS_ID_MSK, val);
+
+ return 0;
+}
+
+static ssize_t retimer_A_mode_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct n3000_nios *nn = dev_get_drvdata(dev);
+ unsigned int mode;
+ int ret;
+
+ ret = get_retimer_mode(nn, N3000_NIOS_PKVL_A_MODE_STS, &mode);
+ if (ret)
+ return ret;
+
+ return sysfs_emit(buf, "0x%x\n", mode);
+}
+static DEVICE_ATTR_RO(retimer_A_mode);
+
+static ssize_t retimer_B_mode_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct n3000_nios *nn = dev_get_drvdata(dev);
+ unsigned int mode;
+ int ret;
+
+ ret = get_retimer_mode(nn, N3000_NIOS_PKVL_B_MODE_STS, &mode);
+ if (ret)
+ return ret;
+
+ return sysfs_emit(buf, "0x%x\n", mode);
+}
+static DEVICE_ATTR_RO(retimer_B_mode);
+
+static ssize_t fec_mode_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ unsigned int val, retimer_a_mode, retimer_b_mode, fec_modes;
+ struct n3000_nios *nn = dev_get_drvdata(dev);
+ int ret;
+
+ /* FEC mode setting is not supported in early FW versions */
+ ret = regmap_read(nn->regmap, N3000_NIOS_FW_VERSION, &val);
+ if (ret)
+ return ret;
+
+ if (FIELD_GET(N3000_NIOS_FW_VERSION_MAJOR, val) < 3)
+ return sysfs_emit(buf, "not supported\n");
+
+ /* If no 25G links, FEC mode setting is not supported either */
+ ret = get_retimer_mode(nn, N3000_NIOS_PKVL_A_MODE_STS, &retimer_a_mode);
+ if (ret)
+ return ret;
+
+ ret = get_retimer_mode(nn, N3000_NIOS_PKVL_B_MODE_STS, &retimer_b_mode);
+ if (ret)
+ return ret;
+
+ if (!IS_RETIMER_FEC_SUPPORTED(retimer_a_mode) &&
+ !IS_RETIMER_FEC_SUPPORTED(retimer_b_mode))
+ return sysfs_emit(buf, "not supported\n");
+
+ /* get the valid FEC mode for 25G links */
+ ret = regmap_read(nn->regmap, N3000_NIOS_INIT, &val);
+ if (ret)
+ return ret;
+
+ /*
+ * FEC mode should always be the same for all links, as we set them
+ * in this way.
+ */
+ fec_modes = (val & N3000_NIOS_INIT_REQ_FEC_MODE_MSK_ALL);
+ if (fec_modes == N3000_NIOS_INIT_REQ_FEC_MODE_NO_ALL)
+ return sysfs_emit(buf, "no\n");
+ else if (fec_modes == N3000_NIOS_INIT_REQ_FEC_MODE_KR_ALL)
+ return sysfs_emit(buf, "kr\n");
+ else if (fec_modes == N3000_NIOS_INIT_REQ_FEC_MODE_RS_ALL)
+ return sysfs_emit(buf, "rs\n");
+
+ return -EFAULT;
+}
+static DEVICE_ATTR_RO(fec_mode);
+
+static struct attribute *n3000_nios_attrs[] = {
+ &dev_attr_nios_fw_version.attr,
+ &dev_attr_retimer_A_mode.attr,
+ &dev_attr_retimer_B_mode.attr,
+ &dev_attr_fec_mode.attr,
+ NULL,
+};
+ATTRIBUTE_GROUPS(n3000_nios);
+
+static int n3000_nios_init_done_check(struct n3000_nios *nn)
+{
+ unsigned int val, state_a, state_b;
+ struct device *dev = nn->dev;
+ int ret, ret2;
+
+ /*
+ * The SPI is shared by the Nios core inside the FPGA, Nios will use
+ * this SPI master to do some one time initialization after power up,
+ * and then release the control to OS. The driver needs to poll on
+ * INIT_DONE to see when driver could take the control.
+ *
+ * Please note that after Nios firmware version 3.0.0, INIT_START is
+ * introduced, so driver needs to trigger START firstly and then check
+ * INIT_DONE.
+ */
+
+ ret = regmap_read(nn->regmap, N3000_NIOS_FW_VERSION, &val);
+ if (ret)
+ return ret;
+
+ /*
+ * If Nios version register is totally uninitialized(== 0x0), then the
+ * Nios firmware is missing. So host could take control of SPI master
+ * safely, but initialization work for Nios is not done. To restore the
+ * card, we need to reprogram a new Nios firmware via the BMC chip on
+ * SPI bus. So the driver doesn't error out, it continues to create the
+ * spi controller device and spi_board_info for BMC.
+ */
+ if (val == 0) {
+ dev_err(dev, "Nios version reg = 0x%x, skip INIT_DONE check, but the retimer may be uninitialized\n",
+ val);
+ return 0;
+ }
+
+ if (FIELD_GET(N3000_NIOS_FW_VERSION_MAJOR, val) >= 3) {
+ /* read NIOS_INIT to check if retimer initialization is done */
+ ret = regmap_read(nn->regmap, N3000_NIOS_INIT, &val);
+ if (ret)
+ return ret;
+
+ /* check if retimers are initialized already */
+ if (val & (N3000_NIOS_INIT_DONE | N3000_NIOS_INIT_START))
+ goto nios_init_done;
+
+ /* configure FEC mode per module param */
+ val = N3000_NIOS_INIT_START;
+
+ /*
+ * When the retimer is to be set to 10G mode, there is no FEC
+ * mode setting, so the REQ_FEC_MODE field will be ignored by
+ * Nios firmware in this case. But we should still fill the FEC
+ * mode field cause host could not get the retimer working mode
+ * until the Nios init is done.
+ *
+ * For now the driver doesn't support the retimer FEC mode
+ * switching per user's request. It is always set to Reed
+ * Solomon FEC.
+ *
+ * The driver will set the same FEC mode for all links.
+ */
+ val |= N3000_NIOS_INIT_REQ_FEC_MODE_RS_ALL;
+
+ ret = regmap_write(nn->regmap, N3000_NIOS_INIT, val);
+ if (ret)
+ return ret;
+ }
+
+nios_init_done:
+ /* polls on NIOS_INIT_DONE */
+ ret = regmap_read_poll_timeout(nn->regmap, N3000_NIOS_INIT, val,
+ val & N3000_NIOS_INIT_DONE,
+ N3000_NIOS_INIT_TIME_INTV,
+ N3000_NIOS_INIT_TIMEOUT);
+ if (ret)
+ dev_err(dev, "NIOS_INIT_DONE %s\n",
+ (ret == -ETIMEDOUT) ? "timed out" : "check error");
+
+ ret2 = regmap_read(nn->regmap, N3000_NIOS_PKVL_A_MODE_STS, &state_a);
+ if (ret2)
+ return ret2;
+
+ ret2 = regmap_read(nn->regmap, N3000_NIOS_PKVL_B_MODE_STS, &state_b);
+ if (ret2)
+ return ret2;
+
+ if (!ret) {
+ /*
+ * After INIT_DONE is detected, it still needs to check if the
+ * Nios firmware reports any error during the retimer
+ * configuration.
+ */
+ if (IS_MODE_STATUS_OK(state_a) && IS_MODE_STATUS_OK(state_b))
+ return 0;
+
+ /*
+ * If the retimer configuration is failed, the Nios firmware
+ * will still release the spi controller for host to
+ * communicate with the BMC. It makes possible for people to
+ * reprogram a new Nios firmware and restore the card. So the
+ * driver doesn't error out, it continues to create the spi
+ * controller device and spi_board_info for BMC.
+ */
+ dev_err(dev, "NIOS_INIT_DONE OK, but err on retimer init\n");
+ }
+
+ dev_err(nn->dev, "PKVL_A_MODE_STS 0x%x\n", state_a);
+ dev_err(nn->dev, "PKVL_B_MODE_STS 0x%x\n", state_b);
+
+ return ret;
+}
+
+static struct spi_board_info m10_n3000_info = {
+ .modalias = "m10-n3000",
+ .max_speed_hz = 12500000,
+ .bus_num = 0,
+ .chip_select = 0,
+};
+
+static int create_altera_spi_controller(struct n3000_nios *nn)
+{
+ struct altera_spi_platform_data pdata = { 0 };
+ struct platform_device_info pdevinfo = { 0 };
+ void __iomem *base = nn->base;
+ u64 v;
+
+ v = readq(base + N3000_NS_PARAM);
+
+ pdata.mode_bits = SPI_CS_HIGH;
+ if (FIELD_GET(N3000_NS_PARAM_CLK_POL, v))
+ pdata.mode_bits |= SPI_CPOL;
+ if (FIELD_GET(N3000_NS_PARAM_CLK_PHASE, v))
+ pdata.mode_bits |= SPI_CPHA;
+
+ pdata.num_chipselect = FIELD_GET(N3000_NS_PARAM_NUM_CS, v);
+ pdata.bits_per_word_mask =
+ SPI_BPW_RANGE_MASK(1, FIELD_GET(N3000_NS_PARAM_DATA_WIDTH, v));
+
+ pdata.num_devices = 1;
+ pdata.devices = &m10_n3000_info;
+
+ dev_dbg(nn->dev, "%s cs %u bpm 0x%x mode 0x%x\n", __func__,
+ pdata.num_chipselect, pdata.bits_per_word_mask,
+ pdata.mode_bits);
+
+ pdevinfo.name = "subdev_spi_altera";
+ pdevinfo.id = PLATFORM_DEVID_AUTO;
+ pdevinfo.parent = nn->dev;
+ pdevinfo.data = &pdata;
+ pdevinfo.size_data = sizeof(pdata);
+
+ nn->altera_spi = platform_device_register_full(&pdevinfo);
+ return PTR_ERR_OR_ZERO(nn->altera_spi);
+}
+
+static void destroy_altera_spi_controller(struct n3000_nios *nn)
+{
+ platform_device_unregister(nn->altera_spi);
+}
+
+static int n3000_nios_poll_stat_timeout(void __iomem *base, u64 *v)
+{
+ int loops;
+
+ /*
+ * We don't use the time based timeout here for performance.
+ *
+ * The regbus read/write is on the critical path of Intel PAC N3000
+ * image programing. The time based timeout checking will add too much
+ * overhead on it. Usually the state changes in 1 or 2 loops on the
+ * test server, and we set 10000 times loop here for safety.
+ */
+ for (loops = N3000_NIOS_REGBUS_RETRY_COUNT; loops > 0 ; loops--) {
+ *v = readq(base + N3000_NS_STAT);
+ if (*v & N3000_NS_STAT_RW_VAL)
+ break;
+ cpu_relax();
+ }
+
+ return (loops > 0) ? 0 : -ETIMEDOUT;
+}
+
+static int n3000_nios_reg_write(void *context, unsigned int reg, unsigned int val)
+{
+ struct n3000_nios *nn = context;
+ u64 v;
+ int ret;
+
+ v = FIELD_PREP(N3000_NS_CTRL_CMD_MSK, N3000_NS_CTRL_CMD_WR) |
+ FIELD_PREP(N3000_NS_CTRL_ADDR, reg) |
+ FIELD_PREP(N3000_NS_CTRL_WR_DATA, val);
+ writeq(v, nn->base + N3000_NS_CTRL);
+
+ ret = n3000_nios_poll_stat_timeout(nn->base, &v);
+ if (ret)
+ dev_err(nn->dev, "fail to write reg 0x%x val 0x%x: %d\n",
+ reg, val, ret);
+
+ return ret;
+}
+
+static int n3000_nios_reg_read(void *context, unsigned int reg, unsigned int *val)
+{
+ struct n3000_nios *nn = context;
+ u64 v;
+ int ret;
+
+ v = FIELD_PREP(N3000_NS_CTRL_CMD_MSK, N3000_NS_CTRL_CMD_RD) |
+ FIELD_PREP(N3000_NS_CTRL_ADDR, reg);
+ writeq(v, nn->base + N3000_NS_CTRL);
+
+ ret = n3000_nios_poll_stat_timeout(nn->base, &v);
+ if (ret)
+ dev_err(nn->dev, "fail to read reg 0x%x: %d\n", reg, ret);
+ else
+ *val = FIELD_GET(N3000_NS_STAT_RD_DATA, v);
+
+ return ret;
+}
+
+static const struct regmap_config n3000_nios_regbus_cfg = {
+ .reg_bits = 32,
+ .reg_stride = 4,
+ .val_bits = 32,
+ .fast_io = true,
+
+ .reg_write = n3000_nios_reg_write,
+ .reg_read = n3000_nios_reg_read,
+};
+
+static int n3000_nios_probe(struct dfl_device *ddev)
+{
+ struct device *dev = &ddev->dev;
+ struct n3000_nios *nn;
+ int ret;
+
+ nn = devm_kzalloc(dev, sizeof(*nn), GFP_KERNEL);
+ if (!nn)
+ return -ENOMEM;
+
+ dev_set_drvdata(&ddev->dev, nn);
+
+ nn->dev = dev;
+
+ nn->base = devm_ioremap_resource(&ddev->dev, &ddev->mmio_res);
+ if (IS_ERR(nn->base))
+ return PTR_ERR(nn->base);
+
+ nn->regmap = devm_regmap_init(dev, NULL, nn, &n3000_nios_regbus_cfg);
+ if (IS_ERR(nn->regmap))
+ return PTR_ERR(nn->regmap);
+
+ ret = n3000_nios_init_done_check(nn);
+ if (ret)
+ return ret;
+
+ ret = create_altera_spi_controller(nn);
+ if (ret)
+ dev_err(dev, "altera spi controller create failed: %d\n", ret);
+
+ return ret;
+}
+
+static void n3000_nios_remove(struct dfl_device *ddev)
+{
+ struct n3000_nios *nn = dev_get_drvdata(&ddev->dev);
+
+ destroy_altera_spi_controller(nn);
+}
+
+#define FME_FEATURE_ID_N3000_NIOS 0xd
+
+static const struct dfl_device_id n3000_nios_ids[] = {
+ { FME_ID, FME_FEATURE_ID_N3000_NIOS },
+ { }
+};
+MODULE_DEVICE_TABLE(dfl, n3000_nios_ids);
+
+static struct dfl_driver n3000_nios_driver = {
+ .drv = {
+ .name = "dfl-n3000-nios",
+ .dev_groups = n3000_nios_groups,
+ },
+ .id_table = n3000_nios_ids,
+ .probe = n3000_nios_probe,
+ .remove = n3000_nios_remove,
+};
+
+module_dfl_driver(n3000_nios_driver);
+
+MODULE_DESCRIPTION("Driver for Nios private feature on Intel PAC N3000");
+MODULE_AUTHOR("Intel Corporation");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/fpga/dfl-pci.c b/drivers/fpga/dfl-pci.c
index a2203d03c9e2..b44523ea8c91 100644
--- a/drivers/fpga/dfl-pci.c
+++ b/drivers/fpga/dfl-pci.c
@@ -27,6 +27,14 @@
#define DRV_VERSION "0.8"
#define DRV_NAME "dfl-pci"
+#define PCI_VSEC_ID_INTEL_DFLS 0x43
+
+#define PCI_VNDR_DFLS_CNT 0x8
+#define PCI_VNDR_DFLS_RES 0xc
+
+#define PCI_VNDR_DFLS_RES_BAR_MASK GENMASK(2, 0)
+#define PCI_VNDR_DFLS_RES_OFF_MASK GENMASK(31, 3)
+
struct cci_drvdata {
struct dfl_fpga_cdev *cdev; /* container device */
};
@@ -61,14 +69,16 @@ static void cci_pci_free_irq(struct pci_dev *pcidev)
}
/* PCI Device ID */
-#define PCIE_DEVICE_ID_PF_INT_5_X 0xBCBD
-#define PCIE_DEVICE_ID_PF_INT_6_X 0xBCC0
-#define PCIE_DEVICE_ID_PF_DSC_1_X 0x09C4
-#define PCIE_DEVICE_ID_INTEL_PAC_N3000 0x0B30
+#define PCIE_DEVICE_ID_PF_INT_5_X 0xBCBD
+#define PCIE_DEVICE_ID_PF_INT_6_X 0xBCC0
+#define PCIE_DEVICE_ID_PF_DSC_1_X 0x09C4
+#define PCIE_DEVICE_ID_INTEL_PAC_N3000 0x0B30
+#define PCIE_DEVICE_ID_INTEL_PAC_D5005 0x0B2B
/* VF Device */
-#define PCIE_DEVICE_ID_VF_INT_5_X 0xBCBF
-#define PCIE_DEVICE_ID_VF_INT_6_X 0xBCC1
-#define PCIE_DEVICE_ID_VF_DSC_1_X 0x09C5
+#define PCIE_DEVICE_ID_VF_INT_5_X 0xBCBF
+#define PCIE_DEVICE_ID_VF_INT_6_X 0xBCC1
+#define PCIE_DEVICE_ID_VF_DSC_1_X 0x09C5
+#define PCIE_DEVICE_ID_INTEL_PAC_D5005_VF 0x0B2C
static struct pci_device_id cci_pcie_id_tbl[] = {
{PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCIE_DEVICE_ID_PF_INT_5_X),},
@@ -78,6 +88,8 @@ static struct pci_device_id cci_pcie_id_tbl[] = {
{PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCIE_DEVICE_ID_PF_DSC_1_X),},
{PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCIE_DEVICE_ID_VF_DSC_1_X),},
{PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCIE_DEVICE_ID_INTEL_PAC_N3000),},
+ {PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCIE_DEVICE_ID_INTEL_PAC_D5005),},
+ {PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCIE_DEVICE_ID_INTEL_PAC_D5005_VF),},
{0,}
};
MODULE_DEVICE_TABLE(pci, cci_pcie_id_tbl);
@@ -119,49 +131,94 @@ static int *cci_pci_create_irq_table(struct pci_dev *pcidev, unsigned int nvec)
return table;
}
-/* enumerate feature devices under pci device */
-static int cci_enumerate_feature_devs(struct pci_dev *pcidev)
+static int find_dfls_by_vsec(struct pci_dev *pcidev, struct dfl_fpga_enum_info *info)
{
- struct cci_drvdata *drvdata = pci_get_drvdata(pcidev);
- int port_num, bar, i, nvec, ret = 0;
- struct dfl_fpga_enum_info *info;
- struct dfl_fpga_cdev *cdev;
+ u32 bir, offset, vndr_hdr, dfl_cnt, dfl_res;
+ int dfl_res_off, i, bars, voff = 0;
resource_size_t start, len;
- void __iomem *base;
- int *irq_table;
- u32 offset;
- u64 v;
- /* allocate enumeration info via pci_dev */
- info = dfl_fpga_enum_info_alloc(&pcidev->dev);
- if (!info)
- return -ENOMEM;
+ while ((voff = pci_find_next_ext_capability(pcidev, voff, PCI_EXT_CAP_ID_VNDR))) {
+ vndr_hdr = 0;
+ pci_read_config_dword(pcidev, voff + PCI_VNDR_HEADER, &vndr_hdr);
- /* add irq info for enumeration if the device support irq */
- nvec = cci_pci_alloc_irq(pcidev);
- if (nvec < 0) {
- dev_err(&pcidev->dev, "Fail to alloc irq %d.\n", nvec);
- ret = nvec;
- goto enum_info_free_exit;
- } else if (nvec) {
- irq_table = cci_pci_create_irq_table(pcidev, nvec);
- if (!irq_table) {
- ret = -ENOMEM;
- goto irq_free_exit;
+ if (PCI_VNDR_HEADER_ID(vndr_hdr) == PCI_VSEC_ID_INTEL_DFLS &&
+ pcidev->vendor == PCI_VENDOR_ID_INTEL)
+ break;
+ }
+
+ if (!voff) {
+ dev_dbg(&pcidev->dev, "%s no DFL VSEC found\n", __func__);
+ return -ENODEV;
+ }
+
+ dfl_cnt = 0;
+ pci_read_config_dword(pcidev, voff + PCI_VNDR_DFLS_CNT, &dfl_cnt);
+ if (dfl_cnt > PCI_STD_NUM_BARS) {
+ dev_err(&pcidev->dev, "%s too many DFLs %d > %d\n",
+ __func__, dfl_cnt, PCI_STD_NUM_BARS);
+ return -EINVAL;
+ }
+
+ dfl_res_off = voff + PCI_VNDR_DFLS_RES;
+ if (dfl_res_off + (dfl_cnt * sizeof(u32)) > PCI_CFG_SPACE_EXP_SIZE) {
+ dev_err(&pcidev->dev, "%s DFL VSEC too big for PCIe config space\n",
+ __func__);
+ return -EINVAL;
+ }
+
+ for (i = 0, bars = 0; i < dfl_cnt; i++, dfl_res_off += sizeof(u32)) {
+ dfl_res = GENMASK(31, 0);
+ pci_read_config_dword(pcidev, dfl_res_off, &dfl_res);
+
+ bir = dfl_res & PCI_VNDR_DFLS_RES_BAR_MASK;
+ if (bir >= PCI_STD_NUM_BARS) {
+ dev_err(&pcidev->dev, "%s bad bir number %d\n",
+ __func__, bir);
+ return -EINVAL;
}
- ret = dfl_fpga_enum_info_add_irq(info, nvec, irq_table);
- kfree(irq_table);
- if (ret)
- goto irq_free_exit;
+ if (bars & BIT(bir)) {
+ dev_err(&pcidev->dev, "%s DFL for BAR %d already specified\n",
+ __func__, bir);
+ return -EINVAL;
+ }
+
+ bars |= BIT(bir);
+
+ len = pci_resource_len(pcidev, bir);
+ offset = dfl_res & PCI_VNDR_DFLS_RES_OFF_MASK;
+ if (offset >= len) {
+ dev_err(&pcidev->dev, "%s bad offset %u >= %pa\n",
+ __func__, offset, &len);
+ return -EINVAL;
+ }
+
+ dev_dbg(&pcidev->dev, "%s BAR %d offset 0x%x\n", __func__, bir, offset);
+
+ len -= offset;
+
+ start = pci_resource_start(pcidev, bir) + offset;
+
+ dfl_fpga_enum_info_add_dfl(info, start, len);
}
- /* start to find Device Feature List in Bar 0 */
+ return 0;
+}
+
+/* default method of finding dfls starting at offset 0 of bar 0 */
+static int find_dfls_by_default(struct pci_dev *pcidev,
+ struct dfl_fpga_enum_info *info)
+{
+ int port_num, bar, i, ret = 0;
+ resource_size_t start, len;
+ void __iomem *base;
+ u32 offset;
+ u64 v;
+
+ /* start to find Device Feature List from Bar 0 */
base = cci_pci_ioremap_bar0(pcidev);
- if (!base) {
- ret = -ENOMEM;
- goto irq_free_exit;
- }
+ if (!base)
+ return -ENOMEM;
/*
* PF device has FME and Ports/AFUs, and VF device only has one
@@ -208,12 +265,54 @@ static int cci_enumerate_feature_devs(struct pci_dev *pcidev)
dfl_fpga_enum_info_add_dfl(info, start, len);
} else {
ret = -ENODEV;
- goto irq_free_exit;
}
/* release I/O mappings for next step enumeration */
pcim_iounmap_regions(pcidev, BIT(0));
+ return ret;
+}
+
+/* enumerate feature devices under pci device */
+static int cci_enumerate_feature_devs(struct pci_dev *pcidev)
+{
+ struct cci_drvdata *drvdata = pci_get_drvdata(pcidev);
+ struct dfl_fpga_enum_info *info;
+ struct dfl_fpga_cdev *cdev;
+ int nvec, ret = 0;
+ int *irq_table;
+
+ /* allocate enumeration info via pci_dev */
+ info = dfl_fpga_enum_info_alloc(&pcidev->dev);
+ if (!info)
+ return -ENOMEM;
+
+ /* add irq info for enumeration if the device support irq */
+ nvec = cci_pci_alloc_irq(pcidev);
+ if (nvec < 0) {
+ dev_err(&pcidev->dev, "Fail to alloc irq %d.\n", nvec);
+ ret = nvec;
+ goto enum_info_free_exit;
+ } else if (nvec) {
+ irq_table = cci_pci_create_irq_table(pcidev, nvec);
+ if (!irq_table) {
+ ret = -ENOMEM;
+ goto irq_free_exit;
+ }
+
+ ret = dfl_fpga_enum_info_add_irq(info, nvec, irq_table);
+ kfree(irq_table);
+ if (ret)
+ goto irq_free_exit;
+ }
+
+ ret = find_dfls_by_vsec(pcidev, info);
+ if (ret == -ENODEV)
+ ret = find_dfls_by_default(pcidev, info);
+
+ if (ret)
+ goto irq_free_exit;
+
/* start enumeration with prepared enumeration information */
cdev = dfl_fpga_feature_devs_enumerate(info);
if (IS_ERR(cdev)) {
diff --git a/drivers/fpga/dfl.c b/drivers/fpga/dfl.c
index b450870b75ed..511b20ff35a3 100644
--- a/drivers/fpga/dfl.c
+++ b/drivers/fpga/dfl.c
@@ -10,6 +10,7 @@
* Wu Hao <hao.wu@intel.com>
* Xiao Guangrong <guangrong.xiao@linux.intel.com>
*/
+#include <linux/dfl.h>
#include <linux/fpga-dfl.h>
#include <linux/module.h>
#include <linux/uaccess.h>
@@ -298,8 +299,7 @@ static int dfl_bus_uevent(struct device *dev, struct kobj_uevent_env *env)
{
struct dfl_device *ddev = to_dfl_dev(dev);
- /* The type has 4 valid bits and feature_id has 12 valid bits */
- return add_uevent_var(env, "MODALIAS=dfl:t%01Xf%03X",
+ return add_uevent_var(env, "MODALIAS=dfl:t%04Xf%04X",
ddev->type, ddev->feature_id);
}
diff --git a/drivers/fpga/dfl.h b/drivers/fpga/dfl.h
index 5dc758f655b7..2b82c96ba56c 100644
--- a/drivers/fpga/dfl.h
+++ b/drivers/fpga/dfl.h
@@ -22,6 +22,7 @@
#include <linux/interrupt.h>
#include <linux/iopoll.h>
#include <linux/io-64-nonatomic-lo-hi.h>
+#include <linux/mod_devicetable.h>
#include <linux/platform_device.h>
#include <linux/slab.h>
#include <linux/uuid.h>
@@ -516,88 +517,4 @@ long dfl_feature_ioctl_set_irq(struct platform_device *pdev,
struct dfl_feature *feature,
unsigned long arg);
-/**
- * enum dfl_id_type - define the DFL FIU types
- */
-enum dfl_id_type {
- FME_ID,
- PORT_ID,
- DFL_ID_MAX,
-};
-
-/**
- * struct dfl_device_id - dfl device identifier
- * @type: contains 4 bits DFL FIU type of the device. See enum dfl_id_type.
- * @feature_id: contains 12 bits feature identifier local to its DFL FIU type.
- * @driver_data: driver specific data.
- */
-struct dfl_device_id {
- u8 type;
- u16 feature_id;
- unsigned long driver_data;
-};
-
-/**
- * struct dfl_device - represent an dfl device on dfl bus
- *
- * @dev: generic device interface.
- * @id: id of the dfl device.
- * @type: type of DFL FIU of the device. See enum dfl_id_type.
- * @feature_id: 16 bits feature identifier local to its DFL FIU type.
- * @mmio_res: mmio resource of this dfl device.
- * @irqs: list of Linux IRQ numbers of this dfl device.
- * @num_irqs: number of IRQs supported by this dfl device.
- * @cdev: pointer to DFL FPGA container device this dfl device belongs to.
- * @id_entry: matched id entry in dfl driver's id table.
- */
-struct dfl_device {
- struct device dev;
- int id;
- u8 type;
- u16 feature_id;
- struct resource mmio_res;
- int *irqs;
- unsigned int num_irqs;
- struct dfl_fpga_cdev *cdev;
- const struct dfl_device_id *id_entry;
-};
-
-/**
- * struct dfl_driver - represent an dfl device driver
- *
- * @drv: driver model structure.
- * @id_table: pointer to table of device IDs the driver is interested in.
- * { } member terminated.
- * @probe: mandatory callback for device binding.
- * @remove: callback for device unbinding.
- */
-struct dfl_driver {
- struct device_driver drv;
- const struct dfl_device_id *id_table;
-
- int (*probe)(struct dfl_device *dfl_dev);
- void (*remove)(struct dfl_device *dfl_dev);
-};
-
-#define to_dfl_dev(d) container_of(d, struct dfl_device, dev)
-#define to_dfl_drv(d) container_of(d, struct dfl_driver, drv)
-
-/*
- * use a macro to avoid include chaining to get THIS_MODULE.
- */
-#define dfl_driver_register(drv) \
- __dfl_driver_register(drv, THIS_MODULE)
-int __dfl_driver_register(struct dfl_driver *dfl_drv, struct module *owner);
-void dfl_driver_unregister(struct dfl_driver *dfl_drv);
-
-/*
- * module_dfl_driver() - Helper macro for drivers that don't do
- * anything special in module init/exit. This eliminates a lot of
- * boilerplate. Each module may only use this macro once, and
- * calling it replaces module_init() and module_exit().
- */
-#define module_dfl_driver(__dfl_driver) \
- module_driver(__dfl_driver, dfl_driver_register, \
- dfl_driver_unregister)
-
#endif /* __FPGA_DFL_H */
diff --git a/drivers/fpga/fpga-bridge.c b/drivers/fpga/fpga-bridge.c
index 2deccacc3aa7..e9266b2a357f 100644
--- a/drivers/fpga/fpga-bridge.c
+++ b/drivers/fpga/fpga-bridge.c
@@ -17,7 +17,7 @@ static DEFINE_IDA(fpga_bridge_ida);
static struct class *fpga_bridge_class;
/* Lock for adding/removing bridges to linked lists*/
-static spinlock_t bridge_list_lock;
+static DEFINE_SPINLOCK(bridge_list_lock);
/**
* fpga_bridge_enable - Enable transactions on the bridge
@@ -479,8 +479,6 @@ static void fpga_bridge_dev_release(struct device *dev)
static int __init fpga_bridge_dev_init(void)
{
- spin_lock_init(&bridge_list_lock);
-
fpga_bridge_class = class_create(THIS_MODULE, "fpga_bridge");
if (IS_ERR(fpga_bridge_class))
return PTR_ERR(fpga_bridge_class);
diff --git a/drivers/fpga/xilinx-pr-decoupler.c b/drivers/fpga/xilinx-pr-decoupler.c
index 7d69af230567..ea2bde6e5bc4 100644
--- a/drivers/fpga/xilinx-pr-decoupler.c
+++ b/drivers/fpga/xilinx-pr-decoupler.c
@@ -1,7 +1,7 @@
// SPDX-License-Identifier: GPL-2.0-only
/*
* Copyright (c) 2017, National Instruments Corp.
- * Copyright (c) 2017, Xilix Inc
+ * Copyright (c) 2017, Xilinx Inc
*
* FPGA Bridge Driver for the Xilinx LogiCORE Partial Reconfiguration
* Decoupler IP Core.
@@ -18,7 +18,12 @@
#define CTRL_CMD_COUPLE 0
#define CTRL_OFFSET 0
+struct xlnx_config_data {
+ const char *name;
+};
+
struct xlnx_pr_decoupler_data {
+ const struct xlnx_config_data *ipconfig;
void __iomem *io_base;
struct clk *clk;
};
@@ -76,15 +81,28 @@ static const struct fpga_bridge_ops xlnx_pr_decoupler_br_ops = {
.enable_show = xlnx_pr_decoupler_enable_show,
};
+static const struct xlnx_config_data decoupler_config = {
+ .name = "Xilinx PR Decoupler",
+};
+
+static const struct xlnx_config_data shutdown_config = {
+ .name = "Xilinx DFX AXI Shutdown Manager",
+};
+
static const struct of_device_id xlnx_pr_decoupler_of_match[] = {
- { .compatible = "xlnx,pr-decoupler-1.00", },
- { .compatible = "xlnx,pr-decoupler", },
+ { .compatible = "xlnx,pr-decoupler-1.00", .data = &decoupler_config },
+ { .compatible = "xlnx,pr-decoupler", .data = &decoupler_config },
+ { .compatible = "xlnx,dfx-axi-shutdown-manager-1.00",
+ .data = &shutdown_config },
+ { .compatible = "xlnx,dfx-axi-shutdown-manager",
+ .data = &shutdown_config },
{},
};
MODULE_DEVICE_TABLE(of, xlnx_pr_decoupler_of_match);
static int xlnx_pr_decoupler_probe(struct platform_device *pdev)
{
+ struct device_node *np = pdev->dev.of_node;
struct xlnx_pr_decoupler_data *priv;
struct fpga_bridge *br;
int err;
@@ -94,17 +112,23 @@ static int xlnx_pr_decoupler_probe(struct platform_device *pdev)
if (!priv)
return -ENOMEM;
+ if (np) {
+ const struct of_device_id *match;
+
+ match = of_match_node(xlnx_pr_decoupler_of_match, np);
+ if (match && match->data)
+ priv->ipconfig = match->data;
+ }
+
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
priv->io_base = devm_ioremap_resource(&pdev->dev, res);
if (IS_ERR(priv->io_base))
return PTR_ERR(priv->io_base);
priv->clk = devm_clk_get(&pdev->dev, "aclk");
- if (IS_ERR(priv->clk)) {
- if (PTR_ERR(priv->clk) != -EPROBE_DEFER)
- dev_err(&pdev->dev, "input clock not found\n");
- return PTR_ERR(priv->clk);
- }
+ if (IS_ERR(priv->clk))
+ return dev_err_probe(&pdev->dev, PTR_ERR(priv->clk),
+ "input clock not found\n");
err = clk_prepare_enable(priv->clk);
if (err) {
@@ -114,7 +138,7 @@ static int xlnx_pr_decoupler_probe(struct platform_device *pdev)
clk_disable(priv->clk);
- br = devm_fpga_bridge_create(&pdev->dev, "Xilinx PR Decoupler",
+ br = devm_fpga_bridge_create(&pdev->dev, priv->ipconfig->name,
&xlnx_pr_decoupler_br_ops, priv);
if (!br) {
err = -ENOMEM;
@@ -125,7 +149,8 @@ static int xlnx_pr_decoupler_probe(struct platform_device *pdev)
err = fpga_bridge_register(br);
if (err) {
- dev_err(&pdev->dev, "unable to register Xilinx PR Decoupler");
+ dev_err(&pdev->dev, "unable to register %s",
+ priv->ipconfig->name);
goto err_clk;
}
diff --git a/drivers/fpga/xilinx-spi.c b/drivers/fpga/xilinx-spi.c
index 27defa98092d..fee4d0abf6bf 100644
--- a/drivers/fpga/xilinx-spi.c
+++ b/drivers/fpga/xilinx-spi.c
@@ -233,25 +233,19 @@ static int xilinx_spi_probe(struct spi_device *spi)
/* PROGRAM_B is active low */
conf->prog_b = devm_gpiod_get(&spi->dev, "prog_b", GPIOD_OUT_LOW);
- if (IS_ERR(conf->prog_b)) {
- dev_err(&spi->dev, "Failed to get PROGRAM_B gpio: %ld\n",
- PTR_ERR(conf->prog_b));
- return PTR_ERR(conf->prog_b);
- }
+ if (IS_ERR(conf->prog_b))
+ return dev_err_probe(&spi->dev, PTR_ERR(conf->prog_b),
+ "Failed to get PROGRAM_B gpio\n");
conf->init_b = devm_gpiod_get_optional(&spi->dev, "init-b", GPIOD_IN);
- if (IS_ERR(conf->init_b)) {
- dev_err(&spi->dev, "Failed to get INIT_B gpio: %ld\n",
- PTR_ERR(conf->init_b));
- return PTR_ERR(conf->init_b);
- }
+ if (IS_ERR(conf->init_b))
+ return dev_err_probe(&spi->dev, PTR_ERR(conf->init_b),
+ "Failed to get INIT_B gpio\n");
conf->done = devm_gpiod_get(&spi->dev, "done", GPIOD_IN);
- if (IS_ERR(conf->done)) {
- dev_err(&spi->dev, "Failed to get DONE gpio: %ld\n",
- PTR_ERR(conf->done));
- return PTR_ERR(conf->done);
- }
+ if (IS_ERR(conf->done))
+ return dev_err_probe(&spi->dev, PTR_ERR(conf->done),
+ "Failed to get DONE gpio\n");
mgr = devm_fpga_mgr_create(&spi->dev,
"Xilinx Slave Serial FPGA Manager",
generated by cgit (git 2.34.1) at 2025-05-30 11:46:38 +0000